流动

The flow regime in downcomer can be divided into two kinds: cross flow injection and impingement. Cross flow injection only takes place under low injection flow rate in dowcomer flow. The investigation on flow regime and heat transfer in RPV under PTS is for the first time in China.

在国内本实验是第一个研究下降环腔内的流动与传热，在国际上，象这样同时进行了流动可视化，常温常压下传热和高温高压下传热的实验也不多，特别是针对下降环腔内对流换热系数的研究，在公开文献中还没有相类似的实验。

The first part of this thesis is concerned with the experimental study and CFD simulation of downer reactors.

本论文使用先进的计算流体力学模拟和非线性分析的方法针对几个重要的流态化过程研究了系统的时均流动行为和瞬态脉动行为，从不同的角度深层次地揭示了气固两相流动过程。

Analyzing and simulating of the deformation law of the ceramic downspout product after overcoming the shortage of powder material models in the software of MSC. MARC. It shows out the important effects of various factors and the shape of mandril during the process. And it is obvious that the shape of the top mandril has more effects on the process than the bottom.(3) Showing out the important effects of model figure on the flowing of powder and the forming of low-density fields from the analysis. After changing the top of the mandril into spherical shape, an improving model is putting out so that the distribution of stress and strain turns to be even and proper and that the flow rule of powder grains is better.(4) Calculating of the dimensional precision and the cutting ratio of the product and analyzing of the effects of such factors as rubber aging, loading process, mandril, friction etc. on the cutting ratio.

MARC存在的粉末材料模型方面的设计缺陷后，对连铸水口粉末成形件的变形规律及影响因素作用进行了模拟分析，指出芯棒形状对成形件的变形有较大影响，并且芯棒顶部形状与芯棒底部形状相比，对粉末变形有更大影响；(3)分析了成形件出现低密度区域的原因，指出模具形状对粉末流动以及粉末成形件低密度区域的形成有重要作用，提出了密度分布优化改进模型：改进模具顶部形状，并将芯棒顶部设计成球面后，粉末成形件顶部区域的应力、应变分布更加均匀、合理，粉体颗粒流动情况明显改善，低密度区域明显缩小；(4)计算了成形件的尺寸精度及切削率，并指出除模具形状的影响外，充填密度、橡胶模具老化、加载工艺等其他因素对总体切削率也有相当的影响。

By means of the K-ε turbulence model and finite element method, the flow of the fluid in the valve and the piston during a cycle of pumping is simulated and calculated. The motion law of the crude oil in the valve passage and concentric annulus in the upstroke and downstroke is analyzed.

针对杆式泵泵简内的流体流动问题，采用湍流模型的K-ε两方程模型和有限元方法，对在一个抽油循环中阀与活塞在几个特定的位置的流体流动进行了建模与计算，具体分析了处于阀道内和同心环状空间中的原油在上下冲程的运动规律。

The smaller the polarity of molecules is, the larger y is. Compared with the single thin-layer cell, the dual thin-layer flow through cell has a higher collection efficiency and transfer efficiency.

与单薄层流动电解池相比，双薄层流动电解池具有较高的收集效率和转移效率。

You can either use a constant flow or an ebb and flow system.

您可以使用一个不断流动或起伏和流动制度。

And direction of factor flows between intermediate sectors are dependent on the quantities of difference in sectoral technical progress and on, elasticity of substitution between intermediate products in the production of the final-product, respectively.

要素流动的速度取决于部门间技术增长率的差异，流动方向取决于中间产品在最终产品生产中的替代弹性。

MF58 mobile electric eye is similar to the phone book of the common handset, differently the white list in MF58 mobile electric eye only records the numbers of authorized users, and up to 20 users record numbers.

MF58 流动电眼上的白名单类似于一般手机上的电话簿，不同的是，MF58 流动电眼上的白名单只记录了授权的用户号码，并且最多记录20个用户号码。

Flow is then stopped, and if the formation has sufficient permeability, the formation will flow to equilibrate the tester with the bulk of the formation.

流动然后停止，而且如果地层有足够的渗透率，地层将会流动，以平衡测试器和地层体积。

The influences of Darcy number and inertia parameter on the velocity profile of the structural flow are analyzed,and it is shown that the velocity profile becomes evener with Darcy number decreasing and the inertia parameter increasing.

随着所施加的外力逐渐增大，管壁附近的各流层依次开始流动，而管路中心的流体仍然以相同的速度，像圆柱体一样向前运动，这部分流体称为流核，流核内部的流层间没有相对运动，具有流核的流体流动称为结构流

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。