法的理论

In the light of the complex, high-level and non-linear feature of the mathematical model which describe the transport of the coalbed methane, this paper study the fully-implicit solving method of the mathematical model in detail. Based on the complexity of the algebraic equations which are formed eventually, according to the alternating direction implicit difference pattern, this paper use the iterative method and the fully main element Gauss-Jordan eliminating method to solve equations, which is to use the iterative method to determine coefficient matrix and use the fully main element Gauss-Jordan method to solve th linear algebraic equation group, at the same time of studying the solving method of the mathematical model, according to the devising requirement of FORTRAN77 program structure, this paper draw up computer program and form the corresponding computer model, and verify the validity and reliability of the model in theory by operating the model.

重点研究了模型内、外边界及有关参数的处理，针对描述煤层甲烷运移的数学模型是一个复杂、高阶非线性数学模型的特点，详细研究了模型的全隐式求解方法，根据最后形成的代数方程组的复杂性，按交替方向隐式差分格式，采用迭代与全选主元高斯约当消去法相结合的方法求解方程：即确定系数矩阵采用迭代法，求解线性方程组时采用全选主元高斯约当消去法，在研究模型解法的同时按FORTRAN结构化程序设计的要求，编制计算机程序，形成相应的CBMRS计算机模型，并通过模型的运行从理论上证明了模型的正确性与可靠性。

The framework established was practical and universal, and could provide abase for specific area to select its assessment indicators. The operable indicatorsystem developed which synthetically reflected the sustainable development status ofliling could fill up the blank of regional sustainable development evaluation in liling,and this work was of practical and strategic significance to a certain extent. Inallusion to the flaw existed indimensionlessness of original data in grey system,mean value method was adopted instead of traditional standardized method, and theguidance for confirming the direction of eigenvector was first brought to grey systemin the application of sustainable development evaluation aimed to increase theobjectivity and accuracy of evaluation. The evaluation results on liling could supplybeneficial references for decision makers to make and adjust sustainabledevelopment strategic goal and counter measures.

本文所构建的区域可持续发展指标体系框架具有实用性和通用性，可作为特定区域在筛选具体评价指标时的参考依据；针对醴陵市建立的区域可持续发展指标体系易于操作，能够综合反映醴陵市可持续发展的各个方面，在很大程度上填补了区域可持续发展评价研究的空白，具有一定的实践意义和战略意义；应用主成分分析法评价各子系统的可持续发展水平时，针对原始数据处理存在的弊端，提出以均值法代替传统的标准法，并首次引入了特征向量确定的原则，从理论上可提高评价的客观性与准确性；对醴陵市区域可持续发展状况的评价结果，可以为醴陵市可持续发展总体战略目标及相关措施的制定与结构调整提供有益参考。

This project was established based on the first cooperative development of optical in situ real time detecting technique probing the atomic scale layer-by-layer epitaxy growth of oxide film. Over the last three years, we have given full play to the advantages and characteristics of both sides and have finished the assumptions and plans of this subject satisfactorily. 1. In Institute of Physics, we set up advanced oblique-incidence reflectivity difference equipment and wrote one data acquisition procedure that made the simultaneous detection of optical signal and RHEED signal into reality. 2. The first observation of sustained oscillations over hundreds of monolayers in both real and imaginary signals during the epitaxy growth of SrNb0.1Ti0.9O3 on SrTiO3 substrate in LMBE testifies that oblique-incidence is an excellent method to detect and monitor film epitaxy growth real time. 3. For the first time, we verify that oblique-incidence reflectivity difference method can be used to monitor the layer-by-layer growth mode during continuous growth through the correspondence between optical signals to atomic or molecular step edge density on the growth surface. 4. Phenomenological analysis shows that optical signals comprise three parts, the first is proportional to the average thickness of the film and depends on the bulk phase dielectric response; the second is proportional to the coverage of terraces and depends on the dielectric response of atoms or unit cells in the terrace; the third is proportional to the coverage of step edges and depends on the effective dielectric response of atoms or unit cells at step edges. This makes oblique-incident reflectivity difference technique a quantitative macroscopic method to monitor film growth.

中文摘要：本课题是在合作首次发展了氧化物薄膜原子尺度层状外延生长光学原位实时探测方法的基础上立项的，三年来，我们充分发挥双方的优势和特点，圆满完成了课题的设想和计划。1、在物理所建立了一套先进的光反射差法装置，编写了计算机系统的数据采集程序，实现了两路光学信号和RHEED数据的同步采集和显示。2、用激光分子束外延在SrTiO3基底上生长SrNb0.1Ti0.9O3薄膜，首次观测到连续外延几百个原胞层，周期振荡的光反射差实部和虚部信号，证明了光反射差法是一种能原位实时探测与监控薄膜层状外延生长的好方法。3、首次验证了通过对生长表面原子或分子台阶密度的响应，光反射差法可用于原位实时监测在连续生长条件下薄膜的层式生长模式。4、通过唯象理论的研究，证明光反射差信号由三项组成，第一项只与薄膜的平均厚度和宏观光学电介质常数有关；第二项与分子台阶面覆盖度和台阶面上分子层的光学电介质常数有关；第三项与台阶边缘的覆盖度成正比，并和在台阶边缘的分子的有效光学介电常数有关。

Beginning with wave equation, the paper has deduced the propagation of gauss pulses in single mode fiber and fiber grating transmission compensation. The characteristics of cascaded phase-shift gratings are discussed by numerical simulations of coupled-mode theory and T-matrix method. The experimental works and measurement results are shown in this paper. On the other hand, we have introduced the basic theory of EDFA and figured out the characteristics for EDFA at different conditions by numerical simulation. Some experimental results for EDFA are also presented here. In this article, you can find the influence on Optical Fiber Amplifier by Gain Tilt, especially, the negative effect on CSO in CATV transmission system.

论文首先从波动方程入手，对高斯脉冲在单模光纤中的传播演化及光纤光栅透射补偿进行了详细的研究；较系统地介绍了光纤光栅的耦合模理论，并将传输矩阵计算法用于计算级连相移光纤光栅的光学特性；重点介绍了作者在光纤光栅刻制及特性测量方面所做的一些实验研究工作；较系统介绍了EDFA的基本理论，计算出各种条件下EDFA的光学特性，并进行了一些实验研究；综合分析光纤放大器对光纤传输系统的影响，特别分析了光纤放大器增益不平坦对光纤CATV系统中CSO恶化的原因及其解决方法，并研究了光纤布拉格光栅在稳定980nm泵浦源输出功率和输出波长方面的应用；结合一个基于光纤光栅和光纤放大器的光纤用户接入网方案，对光纤用户接入网的若干问题进行了理论与初步的实验研究。

In addition, total wheel/rail contact calculation with divided rail outline method are raised. Under the condition of considering the displacement, bouncing, yaw, roll of wheelsets and displacement, bouncing, roll of rails, minimum gap between rail and wheel were calculated by the trochoid method and divided rail outline method, we can easily judge totally real contact states of the wheel/rail such as normal one-point contact, nonnormal one-point contact, two-point contact and wheel complete lift. Wheel/rail normal forces in the two contact point are respectively calculated by nonlinear Hertz contact theory, and then, result of simulation more close to reality on actual track.

另外，提出了轨廓分区法全面计算轮轨接触状态法，在考虑轮对的横移、浮沉、摇头、侧滚和左右钢轨的横移、浮沉、侧滚的条件下，可全面地分别计算左右侧轨顶和轨侧区域与车轮的最小轮轨间隙量，以此来判断轮轨的真实接触状态：正常的一点接触、非正常的一点接触、两点接触和车轮完全悬浮，并根据非线性赫兹接触理论分别求得两接触点处的轮轨法向力，从而使仿真结果更接近于车辆在实际线路上的运行状态。

Chapter 8: We discuss the acceleration of multigrid by Krylov subspace approaches, and recognize the reason for slow convergence of algebraic multigrid methods is that error reduction is significantly less efficient for some very specific error components which may cause a few eigenvalues of the algebraic multigrid iteration matrix to be considerably closer to 1 than all the rest. However, the eigenvectors belonging to the few isolated eigenvalues can be expected to be typically captured after only a few conjugate gradient iterations, which accelerate algebraic multigrid algorithms. Theoretical analysis and numerical results of some practical problems show the iterant recombination accelerates algebraic multigrid convergence.

第八章：先介绍用Krylov子空间迭代法加速一般多重网格方法收敛的基本框架，然后紧紧抓住引起代数多重网格方法收敛减慢的根本原因往往是误差减小对几个特别的误差分量不明显，这导致代数多重网格方法的迭代矩阵的几个特征值接近于1，而共轭梯度方法则能比较典型地捕捉属于孤立特征值的特征向量，从而推导出有效的共轭梯度加速算法和程序实现，不仅从一些具体的实际应用例子的数值结果去验证迭代复合加速收敛的效果，而且还从理论上分析了预处理共轭梯度法加速代数多重网格法收敛的机理。

Secondly, by the analysis of influencing factors of collapsibility of loessal foundation, results indicated that at the basis of the grey incidence analysis on influencing factors of collapsibility of loessal foundation,the void ratio is the superior and steadily influencing factor of collapsibility at all events and other influencing factors will have different degree of influence according to the specific conditions of loess foundation.

通过分析影响黄土湿陷性变形的因素，对于湿陷变形因素的关联分析，可以看出土性指标对湿陷性的影响程度，孔隙比的影响比较突出，基本上可以认为是在土性指标对湿陷性的影响程度中最大的，其它指标会因土质含量、黄土的类型不同而影响各异。总之，本文应用灰色系统理论的关联分析法对应用广泛的工程实用模型变形计算方法做一些因素分析、进行反思，同时证明了弦线模量法计算沉降是值得大力推广的，弦线模量法计算沉降在将来的工程实践中必将带来更为可观的社会经济效益。

The aim of this study was to develop a novel amphiphilic functional block poly(ε-caprolactone) bearing ketone groups MPEG-b-P(OPD-co-CL. 2-oxepane-1, 5-dione was copolymerized with ε-caprolatone in which methoxy poly (MPEG, Mn=5 000) and stannous octoate were used as initiator and catalyst, respectively. The syntheses were conducted by bulk and solution polymerization. 1H NMR results showed that peak position and splitting of the polymers synthesized through solution polymerization were consistent with theoretical data, demonstrating the products were designed block copolymers. While in the bulk polymerization, polymer peak position was changed due to their high reaction temperature, suggesting their structural variation.

将带有羰基官能团的4-羰基己内酯和ε-己内酯分别在甲氧基聚乙二醇(MPEG，Mn=5 000)为引发剂，异辛酸亚锡为催化剂溶液和本体体系中开环聚合，合成了两亲性侧基带有羰基官能团的聚己内酯嵌段共聚物MPEG-b-P(OPD-co-CL.1H NMR结果表明采用溶液聚合法合成的聚合物各峰的峰位置和分裂情况与理论一致，证明了产物是实验所设计的嵌段共聚物，而采用本体聚合法合成的聚合物由于温度的影响，聚合物各峰的峰位置发生了变化，说明其结构发生了变化；差示扫描量热法分析结果表明随着OPD单体含量的增加，聚合物的熔点，玻璃化转变温度和熔融焓增加；热失重测试结果表明OPD单体的引入增加了聚合物的热敏感性。

By the use of Circling cluster and Envlopment theory and flat surface sit-mark transformation theory, the chain wheel tooth equation of roller chain at high speed to match conjugage engagement is deduced.Establishing chain speed equation of roller chain at high speed,based on the analysis of the speed curves between roller chain at high speed and common roller chain,good drive of roller chain at high speed is verificated theoretically.By a example that move distance from transverse vibration between roller chain at high speed and common roller chain is contrasted,the accuracy of those theories that the paper brings up and higher functions of roller chain at high speed is proved.Finally, Establishing conjugage engagement line equation of roller chain at high speed and analyzing the complete engagement zone, the chain wheel tooth curve equation is studied at a higher degree. At the same time,the lack's place of the research result is pointed out.

依据高速滚子链设计要求与H_y-V_0齿形链的研究，阐述了滚子链传动实现准共轭啮合理论可能性；利用圆族包络法结合平面坐标变换理论推导出了满足共轭啮合的高速滚子链的链轮齿廓曲线；建立起高速滚子链链速方程，通过对高速滚子链与普通滚子链链速曲线的对比分析，从理论上验证了高速滚子链具有良好的传动性能；最后，建立起高速滚子链共轭啮合线方程，对其整个啮合区间进行了分析，进一步研究了链轮齿廓曲线方程，确定了主要参数的设计方法的问题，并同时指出了不足之处。

The distribution of thickness rolled and profile are simulated by considering roll system elastic deformation theory, distributions of tension stresses theory and roll thermal crown theory during rolling of wide strip and high speed aluminum foil roughing mill the rolling technology and thermochemistry parameters are tested, etc, the paper verifies above theories.

采用差分法模拟了具有分段冷却装置的宽幅高速铝箔粗轧机轧辊的温度场及热凸度分布。对轧辊热形为特性进行了全面的研究。首次考虑铝箔轧制的辊系弹性变形理论。张应力分布理论及轧辊热变形理论模拟了宽幅高速铝箔粗轧机的轧后断面形状及板形。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。