氧化物

At an electrode potential of +0.87 V, the electrode surface was rich of acicular Sn and stannum oxide. This film would prevent the electrode from dezincification, and the current density decreased and homeostasis was reached at the same time. The corrosion mechanism of brass welded line in artificial seawater was dissolution/redeposition.

随后，电极表面积累的锡和锡的氧化物及腐蚀产物层对脱锌腐蚀有一定的阻碍作用，电流密度有所下降，最后腐蚀达到一种动态平衡，腐蚀机制为溶解－再沉积机理。

The current density peak of brass welded line appeared at -0.012 V, and a porous corrosion film was formed. The electrode was passivated subsequently. The passivation film was made up of Cu2O, CuCl and ZnO. The passivation film dissolved with electrode potential, and displacement deposition took place between Cu and Zn. The copper redeposition on the electrode surface induced the increase of electrode activity and corrosion rate.

黄铜焊缝在电位-0.012V时出现电流峰，腐蚀产物膜多孔、疏松，随后电极进入钝化区，钝化膜由Cu2O、CuCl和ZnO组成；随电位升高，钝化膜溶解，发生铜锌置换反应，沉积的Cu导致活性电对的形成，增加了合金的腐蚀速度；当电位为+0.87V时，电极表面富集了针状锡和锡的氧化物。

The study has shown that MgO has different rules on sinter reducibility at 850℃ and 1220℃, i.e.,it promotes reducibility of sinter at 850℃ and restrains sinter reduction at 1220℃.

研究表明，MgO对烧结产物还原性的影响，在850℃和1220℃显示出不同的规律，低温下抑制铁氧化物的还原，高温下有利于还原性能的改善。

For many years, it has been clear that the well-known antioxidant and cellular reductant, L-ascorbic acid has a significant role in prevention of the cellular damage imposed by ozone.

翻译结果：许多年，它已经是清楚的众所周知的抗氧化物和细胞的 reductant， L-ascorbic 的酸有被新鲜的空气强加的细胞损害的预防的一个重要的角色。

This paper studied the effects of rare earth on the refractoriness and bend strength of vitrified bond.

本文采用正交实验法研究了稀土氧化物La2O3、CeO2、Y2O3对陶瓷结合剂耐火度和强度的影响。

It was found out that when the content of Y2O3 and CeO2 changed from 0%, 2.5% to 4.5% and 0%, 1.5% to 3.5% respectively, the refractoriness changed a little.

实验研究发现稀土氧化物的添加对陶瓷结合剂的耐火度有一定影响，抗折强度也有所变化。Y2O3的含量从0%、2.5%到4.5%变化时，CeO2的含量从0%、1.5%到3.5%变化时对结合剂的耐火度影响不大。

A comparative study of porosity, oxide contents, bond strength and wear resistance of 3Cr13 stainless steel coatings deposited by high velocity and regular arc spray processes was carried out. An orthogonal and rotational regression experimental method and an ordinary single-factor experimental method were adopted to evaluate the coating hardness with respect to the effect of processing parameters. The quantitative formula of processing parameters with coating hardness was obtained by means of microcomputer.

摘 要：对比研究了3Cr13不锈钢高速电弧喷涂涂层和普通电弧喷涂涂层的孔隙率、氧化物含量、涂层结合强度和滑动磨损性能，并采用多因素正交旋转回归设计和单因素对比试验的方法研究了高速电弧喷涂工艺参数对3Cr13不锈钢涂层显微硬度的影响，用微机回归得到了喷涂工艺参数与涂层硬度之间的定量关系式。

A comparative study of porosity, oxide coontents, bond strength and wear resistance of 3Cr13 stainless steel coatings deposited by high velocity and regular arc spray processes was carried out. An orthogonal and rotational regression experimental method and an ordinary single-factor experimental method were adopted to evaluate the coating hardness with respect to the effect of processing parameters. The quantitative formula of processing patameters with coating hardness was obtained by means of microcomputer.The results show that, compared with the regular arc spray process, a dense?

对比研究了3Cr13不锈钢高速电弧喷涂涂层和普通电弧喷涂涂层的孔隙率、氧化物含量、涂层结合强度和滑动磨损性能，并采用多因素正交旋转回归设计和单因素对比试验的方法研究了高速电弧喷涂工艺参数对3Cr13不锈钢涂层显微硬度的影响，用微机回归得到了喷涂工艺参数与涂层硬度之间的定量关系式。

The results show that, compared with the regular arc spray process, a dense coating with lower porosity, higher bond strength and higher oxide contents were produced by a newly developed high velocity arc wire spray process.

结果表明，和普通电弧喷涂涂层相比，高速电弧喷涂涂层组织致密、孔隙率低、涂层氧化物含量增多，涂层－基体界面结合强度大于40？

Coating with lower porosity, higher bond strength and hhigher oxide?contents were produced by a newly developed high velocity arc wire spray process.The bond strength in higher than 40MPa, which is increased by 52 percent than that of regular arc sprayed coatings.

结果表明，和普通电弧喷涂涂层相比，高速电弧喷涂涂层组织致密、孔隙率低、涂层氧化物含量增多，涂层-基体界面结合强度大于40MPa，比普通电弧喷涂提高了52％。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。