氧乙炔的

We developed GkCY16 series pressure sensor; the No, 1 deadfall electronic railroad track scale of China and have carried on the supreme 35t boiler's auto control/operating system. Come to the 2000, the 44 th institute always stick the tide of technique development and recommended many new products.

我所研制生产了宇航卫星用的GKCY16型压力传感器；我国第一台翻车机电子轨道衡、第一台氧--乙炔烧蚀机；同时还承接了我国最大的35T锅炉自动控制与操作系统。

The TiC/Fe composite coatings were prepared by reactive flame spray using ferrotitanium, iron and graphite as the starting materials, which need ignite the self-propagation high-temperature synthesis reaction of Fe-Ti-C system by oxygen-acetylene flame.

在喷涂过程中，在氧乙炔火焰条件下引燃Fe-Ti-C体系的自蔓延高温合成反应，研究该SHS反应的动力学。

When compressed air as plasma gas enthalpy value of the high arc voltage than 100V, power supply voltage of 200V or more30mm thickness of the cut the following materials, have been replaced by an oxyacetylene flame cutting trend.

压缩空气作离子气时热焓值高，弧压100V以上，电源电压200V以上，在切割30mm以下厚度的材料时，已有取代氧乙炔焰切割的趋势。

By adding variable quantities of nano-meter Si3N4 into the ZrO2-Y2O3 ceramics based powder, the ceramic coating was prepared by subsonic speed flame spraying.

通过在ZrO2-Y2O3为基的陶瓷粉体中添加不同质量分数的纳米Si3N4，采用亚音速氧乙炔火焰喷涂制备陶瓷涂层。

The self-fluxing performance of these alloys in oxygen-acetylene flame spray-welding has been observed in detail.

制备了含稀土的铁基自熔合金并考察了这种自熔合金在氧-乙炔火焰喷焊过程中的自熔性。

The strength of coating layer obtained by one-shot self-felt powder with subsonic oxygen-acetylene spraying technique was discussed.

采用亚音速氧乙炔火焰喷涂技术，喷涂一次性自粘结粉末，经测定涂层的结合强度可达到打底层的界面结合强度。

It is suitable to be used as filling material for oxygen-acetylene gas welding and carbon arc welding, and also for manual braze welding. It is the ideal material for welding of copper alloy, copper, gray cast iron and hard alloy knife and etc.

HS221 JIS ZYCusN 适用于氧-乙炔气焊及碳弧焊时作为填充材料，也可用于钎焊，是铜合金、钢、灰铸铁及硬质合金刀具等焊接材料中较为理想的焊接材料。

The self-lubricanting coating of nickel-coated graphite was prepared by oxygen-acetylene flame spraying technology and its friction and wear properties at room temperature were studied in a ball on disk test rig.

选用镍包石墨粉末，采用氧-乙炔火焰喷涂技术制备镍包石墨自润滑涂层，在球-盘摩擦磨损试验机上探讨了室温条件下镍包石墨自润滑涂层的摩擦磨损性能。

The abrasion and scuffing behaviour of Ni-base spray-welded coating containing WC by oxygen-acetylene was studied and compared with those of boride layer using a MM200 wear tester.

利用MM200型磨损试验机研究了氧-乙炔焰镍基碳化钨喷熔层的磨粒磨损和抗咬合特性，并与硼化物层进行了比较。

The results showed that the interlaminar shear strength of modified carbon/phenolic resin composite was reached the maximum 31.17 MPa, the oxygen-acetylene linear ablation rate was the minimum 0.020 mm/s with the content of carbon nanofiber 15%.

结果表明，当纳米炭纤维质量分数为15%时，其改性复合材料的层间剪切强度最大，达到31.17MPa，氧乙炔线烧蚀率最小，为0.020mm/s。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。