气箱

Main structures of plenum pulse bag type collector are as followers: box body and bag compartment, dust store bin, wind inlet and outlet (including screw conveyer and cinder valve), ladder, baluster, air passage system (including offline pneumatic cylinder, electromagnetic pulse valve, compressed air bag), de-dusting controller and so on.

气箱脉冲式袋除尘器的主要结构是，主体由箱体和袋室，灰斗、进出风口（包括螺旋输送机和卸灰阀），爬梯、栏杆、气路系统（包括离线气缸、电磁脉冲阀、压力气包等）、清灰控制器等。

With the requirements of parallelism, flatness, concentricity and

式除尘器用分气箱》的要求外，还应附合如图15所

The pressure correction method is used to calculate the two-dimensional turbulent flow in general curvilinear coordinates.

按照进气箱对称面的形状，给出一种简化的二维进气箱几何模型，用微分方程法生成贴体的曲线网格，在任意曲线坐标系下采用压力修正法数值模拟了其内部二维湍流流动。

The result shows that multiple inlet is better than single inlet, and that inlet with buffer is better than that without buffer. Other optimal design structures are also adopted. The gas manifold with optimal structure make oxygen much evener for each cell.

结果表明多进口比单进口，有比无隔板、扩压型进口比非扩压型进口、椭圆台进口比圆台进口的进气箱结构更易实现电池堆中每个单电池进气量的均匀化。

The relation equation of pressure drop in oil tank vers burning time and the air volume is established.

分析了几种便携式燃烧器系统的特点和应用的热负荷范围；导出了油箱容积、气箱容积、充气间隔的压力降和燃烧时间的关系。

When the flange hole of coal blower casing and inlet box is countersunk, the problem of connecting hole back spot facing can be effectively solved.

它可以有效地解决在锪煤气鼓风机铸铁机壳和进气箱的开箱法兰把接孔时，连接孔背面的锪平问题。

Because of the complex geometry of the inlet box, the finite element method is used to calculate the three dimensional inviscid flow in it.

使用三维粒子动态分析仪首次对进气箱这一风机进口固定导流元件内复杂的气固两相流动进行了详细测量。

Surface of the manifold box by the air pressure in the bag.

密封垫利用分气箱内的空气压力固定在分气箱表面。

At present, the main production engine timing belt cover, cold air intake box assembly, isolators, oil port cover, retaining tube stents, water blocks, outlet, bowl gaskets, intake air temperature sensor plug and universal joints Dustproof, aluminum die-casting products.

目前主要生产发动机正时皮带罩、冷空气进气箱总成、隔离器、机油口盖、护管支架、进水座、出水口、碗形垫片、进气温度传感器堵头及万向节防尘罩、铝压铸等产品。

The simulation results of inlet air manifold show that the uniformity of the velocity at outlet of the manifold are improved by using the appropriate bell-mouthed inlet and clipper-built baffle, and inlet pressure needed of the manifold decrease.

对进气箱的模拟结果表明，采用扩压型进口加流线型挡块的方案可以提高出口速度的均匀性，同时降低了进气箱入口所需的气体压力。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。