气源的

The whole technology of CIGS cells is simple,economical,and without using of toxic gases.

该研究采用的CIGS薄膜太阳能电池的制备工艺简单、过程容易控制、设备和材料费用低，没有采用剧毒的气源，适合大规模产业化的要求，为以后进一步的研究开发做了技术储备。

From dissolved gas model, combined with measured data of reserviors, method for calculation of the beginning degasification of dissolved gas in oil is derived and typical degasification model is constructed.

认为济阳坳陷油溶解气的起始脱气深度大约在1 700～2 000 m之间，埋深小于起始脱气深度，可形成气层气、气顶气和夹层气天然气藏；埋深在起始脱气深度至3 900 m之间，气藏在油中处于欠饱和状态，以溶解气赋存形式为主；深度大于3 900 m，烃源岩才开始进入大量游离气生成阶段，可形成深层原生气藏。

In this year's Beijing International Machine Tool Show (2005 CMIT), the Tianjin-or gold at the full range of products, including air preparation components: regulator, filter, lubrication, drainage, pressure gauges; valve categories: Electromagnetic valve, pipe valve, pneumatic valve, mechanical valve, the valve manually, foot valve; cylinder categories: standard atmospheric pressure bars, mini round-cylinder, micro-cylinder, rotating cylinder, manipulator, welding tanks, cylinder block, a rule Cylinder, no-cylinder, guided-bars and all kinds of buffers, the appearance of refined products, a series of rich and comprehensive feature allows visitors not only praise, so that customers have a better choice.

在今年的北京国际机床展（2005CMIT）上，天津罗升展出了金器全系列产品，包括气源处理组件：调压器、过滤器、润滑器、排水器、压力表；阀类：电磁阀、管路阀、气动阀、机械阀、手动阀、脚踏阀；缸类：标准气压杠、迷你圆型缸、微型缸、旋转缸、机械手、焊接缸、阻挡缸、治具缸、无杆缸、导杆杠及各种缓冲器等，产品精致的外观、丰富的系列、全面的功能让参观者赞叹不止，让客户有了更好的选择。

When the temperature of a substrate is 250 DEG to 650 DEG C, the proportion of antimony doping to ZnO is controlled by adjusting the carrier gas flow rate of antimony metallorganic and zinc metallorganic to grow p type ZnO.

在衬底温度为250℃～650℃时，通过调节锑的金属有机物与锌的金属有机物源的载气流量来控制锑掺入ZnO的比例进行p型ZnO的生长。

The promising regions for Quaternary biogas accumulation and location should meet all the following requirements: adequate biogas source, long time traps, good mothballing conditions and their good association. The Sebei and Tainan areas in the north slope of the Sanhu area are favorable direction of gas migration and should be regarded as targets of next exploration.

充足的气源供给、长期存在的圈闭、良好的封堵条件及其配置良好的区带是第四系生物气藏形成与分布的有利区带，例如该区北斜坡的涩北和台南地区为第四系生物气运移和聚集的最有利区带，易形成大气田，应作为下一步勘探的重点。

Found filling pressure cap low, should be added fillers, such as found in the dry filler PTFE B sclerosis, should be promptly replaced; should pay attention to the inspection tour of the operation of control valve, check valve position indicator and regulator output is anastomosis; on the control valve with positioner should always check gas source, identify problems in time processing; should be kept sanitary control valve as well as parts are ready.

如发现填料压帽压得很低，则应补充填料，如发现聚四氟乙燥填料硬化，则应及时更换；应在巡回检查中注意调节阀的运行情况，检查阀位指示器和调节器输出是否吻合；对有定位器的调节阀要经常检查气源，发现问题及时处理；应经常保持调节阀的卫生以及各部件完整好用。

We produce kinds of Air Cylinder, Direction Control Valve, Gas Generator and etc. with nice sculpt, complete specification, good function and reasonable structure. It's suitable for oil field, textile industry, machinery, electronics industry and etc. It's an ideal product to replace manual operations.

我厂生产的各种气缸、方向控制阀、气源处理件、气动辅助等各类气动产品，品种繁多，规格齐全、外型美观、结构合理、性能优良，该产品适用于油田、纺织、机械、电子等行业的流水线生产，是替代烦琐的手工操作从而达到提速的理想产品之一。

The design of pneumatic elevator using public air resource in rod workshop for 550mm three-high roughing mill is introduced.

介绍了利用棒材生产车间的公共气源，与φ550mm三辊粗轧机配套气动升降台的设计，这种新型气动升降台能满足实际生产要求，具有良好的使用效果。

The steady establishment is meets a standard in this design after the surge tank outside to be mad the source realizes is each component choice.

稳压场的建立在本设计中是通过稳压罐外接一个标准气源来实现的然后是各个器件的选择。

Because the characteristic of the discharge could be strongly affected by the construction of the electrodes, three common used electrodes (direct discharge between two metal electrodes, silent discharge, surface discharge) were analyzed and compared in detail.

结合臭氧形成机理研究，比较了3 种放电形式在产生臭氧方面的特点。研制成功了产品化臭氧发生器，经检测，在使用未经处理的室内空气作为气源时，该发生器的臭氧生成效率为68.44 g／。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。