气泡
- 与 气泡 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Vacuum consolidation test and load consolidation test were performed and compared for different kind of soil samples. After analyzing the results of tests, the four major mechanisms of vacuum consolidation were defined as: variation of capillary potential, drainage of sealed bubbles, vaporization and action of atmosphere pressure, in which, the action of atmosphere pressure is the most important factor.
首先对不同土样进行了一系列室内真空固结和加载固结的对比试验,通过对试验结果的比较分析,明确了抽真空引起土样固结的原因,即抽真空作用会在四个方面对试样产生影响:毛细管势的改变、封闭气泡的排出、汽化现象及大气压的作用,而其中大气压的作用是最主要的。
-
Based on the characteristics of casing annulus gas-venting wells, the particularity of multi-phase flow in the condition that the casing-head gas flows through a nearly stagnant liquid was investigated. Based on the theory of Taylor bubble, a model to calculate void fraction and pressure gradient in various viscosity liquids was developed. This model is applicable to bubbly flow and slug flow.
以泰勒气泡在黏滞流体中的上升流速作为主要依据,建立了不同油黏度下套管环空放气流动的截面含气率和压降计算模型,并提出了不同黏度、不同气油比的套管定压放气井环空流动计算及套管压力分布的多相流模型,该模型主要适用于泡流和段塞流。
-
Bonded degree not strongly, the label paper is not enough material and softness to the skin, that produces bubbles, the label also be detached to Workbench, werenot, mainly due to the pressure-sensitive labels when casting plastic bottle blowing temperature, pressure, cooling temperature respects to strictly control, if the control is not good occur label and body detachment.
粘合度不强,标签纸材质硬、柔软度不够,容易使产品产生气泡,标签也会撕下来,粘固不牢固,主要是因为在贴标时入模塑料温度,吹瓶时的压力、冷却温度等几方面都要严格控制,如果控制不好会出现标纸和瓶身脱离的现象。
-
The effects of rheological characteristics, orifice diameter, chamber volume and gas flowrate on bubble formation were discussed.
讨论了流体流变性质、喷嘴直径、气室体积和气体流率对气泡生成的影响。
-
When chemostats were used to study the Monod kinetic coefficients of garbage digestion under thermophilic condition, it was found that the maximum yield coefficient, the decay coefficient, the maximum specific utilization, and the half-velocity constant were 1.747 mg VSS/mg COD, 0.1191 1/d, 0.326 mg COD/mg VSS-d, and 2715 mg COD/L, respectively.
在温度因子对厨余之水解实验结果方面,热前处理温度设定为37℃、50℃及60℃达84小时后,发现以60℃处理之水解率(18.1%)及油脂去除率(37.7%)最高;将上述经37℃、50℃及60℃处理84小时之厨余,以气泡式呼吸仪实验探讨生物分解性之结果亦显示,以60℃处理时经过约300小时后TCOD去除率79.2%最高。
-
There can be no draw in this game, either you clean all the bubbles off, or they move all the way down on you.
有没有可以借鉴在这场游戏中,无论是您清洁全部气泡的小康,或者他们提出的所有方式,对你。
-
Biologists have found argonauts with air bubbles in their cases, and now it turns out the animals use the trapped air to float at a comfortable depth, says Julian Finn of Museum Victoria in Melbourne, Australia.
生物学家曾经在舡鱼壳内找到气泡,现在才发现舡鱼会利用这些被困在壳内的空气上浮动一定的舒适高度,澳大利亚墨尔本维多利亚博物馆的朱利安·芬介绍说。
-
Once at the surface, argonauts rocked their cases and took on air, he says. Then they positioned body parts to seal in some of the air and jetted downward, leaving behind a trail of bubbles.
舡鱼一旦抵达水面,立刻摆动'盔甲'接近空气,然后,它们会摆好姿势偷吸空气,接着一头扎入水中,身后留下一连串的气泡。
-
Two types effervescent atomizers were tested in this work, Particle Dynamic Analyzer were used to measure and analyze the atomization performances and flow characteristics. A combustion chamber was devised to investigate the combustion characteristics of effervescent atomizers.
为此,本文作者设计了一套多孔气泡雾化喷嘴,在对其雾化特性研究的基础上,本文将着重对该喷嘴的燃烧特性进行实验研究,以得到相关的实验数据来指导和完善喷嘴的设计工作。
-
Therefore, we designed a porous effervescent atomizer. In this paper, experimental investigations have been conducted on the combustion characteristics of effervescent atomizers, and the experimental data could provide guidance for the designing of atomizers.
气泡雾化喷嘴作为一种新型的雾化喷嘴,具有雾化质量高、耗气量小等特点,因此比较适合用于雾化重、渣油等高粘度液体燃料。
- 推荐网络例句
-
I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""
客人们在卡罗利娜·埃凯家里,举止就文雅一些,因为卡罗利娜的母亲治家很严厉。
-
Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.
由著名品牌 Herm è s 设计,这件高贵的制服是香港本土制造,是我们第一套不配帽子的制服。
-
Do not 'inflate' your achievements and/or qualifications or skills .
不要 '夸大' 你的业绩或成果,条件或者技能。