比及

Analyse the distributive law of shear-lag effect and influence of each structural parameter: pile length , bending stiffness of pile, bending stiffness of abutment, abutment length, different type of soil behind abutment, curve radius, width to span ratio,width of beam, etc. And the main influencing parameters were picked up.

进行结构参数分析，研究等代桩长、桩的纵向抗弯刚度、桥台纵向抗弯刚度、桥台高度、台后土压力、曲率半径、宽跨比及箱梁肋板间距等对剪滞系数的影响，从而得到影响无伸缩缝曲线箱梁桥剪力滞效应的主要参数和次要参数。

By mono-factor analysis of the point drip infiltration,the horizontal and vertical movement distance of soil wetting front were not only in close relation with dripper discharge and drop water,but also had good power functional relation which exists with the soil characteristic ( soil density, soil initial moisture).

以室内试验为基础，测定了重壤土、中壤土、砂壤土在不同滴头流量、不同灌水量下的点源入渗运动过程，通过对点源入渗特性的单因子分析表明，湿润锋水平、垂直扩散距离不仅与滴头流量、灌水量关系密切，与土壤特性(土壤容重、初始含水率)也存在良好的幂函数关系，得出了以土壤物理参数和湿润比及湿润深度为基础的点源滴灌滴头流量的设计模式

The mechanical properties, antifreezing nature and utilizable property in roads of efflorescent sand and its mixture produced by Dunhua City was studied in the paper.

并在上述研究的基础上，结合风化山砂在敦化市城市道路施工中的实际应用情况，提出了符合敦化市特点的风化山砂混合料配合比及典型路面结构

During the course of electro form process, we got ideal electro form process condition that can get windings with uniform granule and high compactness, including current waveform, frequency, duty ratio and voltage to the windings ect. Affect of underlay's flatness to the electroform process are also analysed in detail. Compatibility between photoresist and electroforming solution is also solved.

在电铸工艺中，摸索出获得颗粒均匀、致密度高的金属绕组线圈的电铸工艺条件，给出了电铸电流的波形、频率、占空比及电极电压，并对衬底表面不平整度对电铸效果的影响进行了详细分析，解决了电铸过程中光刻胶与电铸液兼容性的问题。

During the course of electro form process, we got ideal electro form process condition that can get windings with uniform granule and high compactness, including current waveform, frequency, duty ratio and voltage to the windings ect. Affect of underlays flatness to the electroform process are also analysed in detail. Compatibility between photoresist and electroforming solution is also solved.

在电铸工艺中，摸索出获得颗粒均匀、致密度高的金属绕组线圈的电铸工艺条件，给出了电铸电流的波形、频率、占空比及电极电压，并对衬底表面不平整度对电铸效果的影响进行了详细分析，解决了电铸过程中光刻胶与电铸液兼容性的问题。

It's shown by experiment and calculation that the main factories of influence on average electron incident angle are electron energy, magnetic lens ratio and target position.

实验和计算都表明，影响平均入射角的因素主要是电子能量、磁透镜比及靶位。

It is found that organic nanotubes from keto-enol isomeric dibenzoylmethane with different diameters show unique size dependent properties according to our experimental and calculated results. With the diameters of the nanotubes decreasing, the enol isomers of DBM molecules increased, the intensity of the fluorescence emission enhanced.

制备了平面稠环分子苝的纳米管，发现纳米管的形成机制源于模板孔洞的高长径比及溶液在高表面能基体上的自发铺展过程，苝层层沉积从而形成纳米管，苝分子头对尾的聚集体是形成纳米管的主要成份。

The relationships of bias and mean square error of EFT with SNR and forgetting coefficient are studied.

该文对EFT的瞬时频率表示偏差、均方差值的统计特性与信噪比及遗忘系数的关系进行了分析，给出了相应的仿真结果。

Corn starch were treated with different dispersant agents including water, alcohol and dimethyl formamide by microwave at different temperatures.

采用微波辐射的手段处理原玉米淀粉，考察了分散剂种类，淀粉与分散剂的质量比及微波处理的温度对淀粉非晶化的影响。

In the paper, the performance of 6102 gasoline engine was studied through the volumetric efficiency analysis.

通过提高压缩比及化油器的匹配调整，使该发动机的经济性提高3％以上。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。