母线

The bus bar from one switchgear to the other switchgear is fixed with the bushing and the ramus bus .

母线从一个开关柜引至另一个开关柜，通过分支母线和套管固定。

The bus bar follows a semi-circle at both ends of the tank and the pipe will conform to the cathode bus bar.

母线如下的半圈，在两端的坦克和管道将符合阴极母线。

Check the amount of the all bus bar installation's accessories before installing bus bar.

Oslash；母线安装前应清点母线安装所需的各项附件。

Based on the platform, a new algorithm for device operating, resisting current transform saturation and identificating bus bar operation mode is proposed.

在此高性能平台下提出了对母线保护装置启动、抗区外故障电流互感器饱和及母线运行方式自适应识别的新算法。

Must ensure that the car has concentric outer circle with the machine tool spindle (Micrometer can be measured on the surface of the workpiece has been processed on the side of the bus and bus).

必须保证已车外圆与机床主轴同心（可用千分表测工件已加工表面的侧母线和上母线）。

For satisfying to process to keep a mother line, arc mother line, whole convex degree, half convex degree, ligarithmic curve cone, cylinder roll son of demand, ability according to design whet to submit have already corresponded form noodles of spiral lead a round, spiral lead Gun, double the song lead Gun, three convex Fengs to lead Gun, and arc plank and other similar of work piece etc..

为满足加工直母线、圆弧母线、全凸度、半凸度、对数曲线圆锥、圆柱滚子的需要，能根据设计磨出具有相应形面的螺旋导轮、螺旋导辊、双曲导辊、三凸峰导辊、以及圆弧支板以及其他类似的工件等。

To the production and technics of switchgear and controlgear assemblies, traditional method usually use rounding interface of coppery and aluminous generatrix level off.

在成套电控设备的铜、铝母线制作工艺过程中，传统的做法是用滚压方式进行铜、铝母线接触面压麻校平。

Busbar in the actual operation of the current great up hundreds of thousands of amperes and voltage is very small, and because of wear and tear resistance fever, If not timely heat, the temperature would increase bus may exceed the allowable temperature, which can affect their work performance, even burn.

母线在实际运行中通过的电流很大可达几十万安培而电压很小，且由于电阻损耗而发热，如不能及时散热，母线温度将升高，可能超过允许温度，从而影响其工作性能，甚至可能烧坏。

Due to the high reliability, high stability and low EMI criterions in auxiliary power supply systems, the half-bridge LLC resonant converter is selected for the front-end converter, the AC bus architecture and full-wave rectifier are as well utilized. The turns-ratio between the AC bus and load converter is 1:1. The effect of beads which are used in the load converters to the resonant circuit is analyzed.

根据辅助电源高可靠性、高稳定性、低电磁干扰、良好的高频隔离的要求，通过对不同拓扑类型的分析比较，选择半桥LLC谐振变换器作为前级变换器，交流母线和零式全波整流结构作为后级变换器，在母线和后级变换器的连接上采用1∶1的隔离变压器连接。

Section of the verticle generatrix will be increased and the verticle generatrix can be adjusted with the loop.

采用该端子后，垂直母线可不用打孔，相对增加了垂直母线的截面利用率，而且可以随回路任意调节。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。