正确性

The result shows that the static state stability limit value of a. c. exciting generator relates to rotor slip.

验证了异步化同步发电机在任一滑差点异步化同步稳定运行时功-角特性的正确性。

The method of bang-bang control of a. c. exciting generator has been verified and the correct results are achived, which lays a foundation to apply a. c. exciting generator in industrial practical operation.

试验验证了异步化同步发电机鲁棒控制方法的正确性和可行性，从而为异步化同步发电机工业实用化运行奠定了基础。

Then the effect of different target extraction algorithms on grating lobes was discussed in detail, a modified method based on 'abnegation method' was developed, which can achieve the optimal result in case of high sampling , simulation results prove that it is feasible.

对舍弃法进行了改进，改进后的舍弃法对自相关函数栅瓣较小的线性调频步进信号在采样率足够高的情况下，可以达到最优的处理结果，仿真结果证明了理论分析的正确性。

The federation is the organic integration of the federates which constructs the simulation system having special functions.

因此，联邦成员的正确性是联邦正确性的前提，决定了仿真系统的成败。

The principle of programming is focused on easy understanding and good use. The basic calculating data of Dahuofang water diversion project is put into the program which the water hammer calculation begins.Part four, uses the advanced Bentley Hammer water hammer calculation software calculates several identical engineering conditions of Dahuofang water diversion project, and then compares the results with the results of programming calculation, and proofreads the accuracy of programming calculation.

程序编好后输进大伙房输水工程的基本计算数据就可以开始进行水锤计算。4、同时使用目前世界上比较先进的&Bentley Hammer&水锤计算软件，计算大伙房输水工程的几个相同工况，所得结果与编写程序计算的结果进行对比，对编写的程序的正确性进行校核。5、在证实了编写程序的正确性，公道性后。

The results indicate that eye scanpaths during imagery phase reenacted those of perception; consistency between eye movements during imagery and perception influenced the correctness of imagery;restricted eye movements during imagery decreased correctness of recall.In experiment 2,eye movements were recorded in the same condition with experiment 1 but prevented rehearsal before imagery.

实验一研究了视知觉条件下表象建构的眼动特征，发现在允许自由眼动的条件下，表象阶段重复了知觉阶段的眼动扫描路径；知觉阶段与表象阶段眼动的一致性影响了表象的正确性；对表象阶段眼动的限制导致表象的正确性显著下降。

This paper using the FEM software Marc, for the 50 and 60 degree V groove of flat plate butt joint simulate the one-layer and three layers welding, finish each welding and cooling it down to room-temperature then start the next welding true represent process and get the temperature field, residual deformation and welding residual stress, according to the theory analysis and empirical equation verified the temperature field and residual deformation all correct, comparison with experiment verified the welding residual stress regularity and correctly.

本文利用有限元软件Marc，对开60°和50°V型坡口的平板对接接头，动态的模拟了单层单道打底焊，焊完一道后让试件冷却到室温以及单层单道满焊，每焊完一道后让试件冷却，然后再焊下一焊道，道间温度≤200℃，在以此为初始边界条件下开始下一道的焊接，真实的再现了焊接过程，得出了温度场，残余变形和残余应力场的分布规律，根据理论分析及经验公式验证了温度场以及残余变形的正确性，角变形的大小，这些结果与数值计算相吻合。通过与实验测得的残余应力进行比较，验证了焊接残余应力的分布规律及模拟的正确性。

Next, using the multiple elements and multiple properties of ANSYS software , we had carried on the two-dimensional coupled simulation to electric field, the flow field and the temperature field of the optimized 3KA rare earth oxide electrolysis cell of the fluoride salt system.

其次，再利用ANSYS多场耦合的特性对优化的3KA稀土氟盐体系氧化物电解槽的电场、流场和温度场进行二维耦合仿真模拟，模拟结果与实际吻合，进一步确定了模拟优化电解槽设计的正确性，验证了耦合模型的正确性。

Furthermore, it presents hardware figuration and software designing based on hold-off angle control and experiments on a prototype induction motor. Then experiment results validate the correctness of theory analyses. In addition, the paper also discusses the effect of soft-starting on shaft torque.

文中首先通过仿真验证了该控制策略的正确性，在此基础上研制了基于关断角控制的感应电动机软起动装置的硬件电路和软件程序，并进行了样机试验，实验结果验证了理论分析的正确性。

This is done by formalising the NSL (Needham-Schroeder-Lowe) protocol and its correctness in Agda, an interactive proof editor, using both the inductive method and strand spaces in Agda.

使用归纳方法和串空间分别将NSL(Needham-Schroeder-Lowe)协议及其正确性在辅助证明系统Agda中形式化，并比较了这两种安全协议验证法，证明两种方法形式化的正确性和攻击者能力是相同的。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。