欧姆

Another approach in enhancing the light extraction efficiency of AlGaInP LED was accomplished using a surface roughening process. In this process, the Au(170 nm)/AuBe(260 nm)/Au(170 nm) ohmic contact layers were first deposited on the GaP window layer. After the alloy annealing process (480°C for 10 min), the Be atoms will diffuse into the GaP top layer and form non-uniform clusters. The LED samples were then immersed into a mixture 3H3PO4:1H2O2:1H2O solution for 6 min, resulting in a rough GaP surface. The luminous intensity of the AlGaInP LED can increase from 42 to 50 mcd, that is, an 18% enhancement can be achieved via the present non-photolithography surface roughening process.Keywords: LED, AlGaInP, Cu substrate, Reflector, Surface roughening

在实验的第二部份是开发磷化镓窗口层之粗化制程，我们是藉由正面金/铍欧姆接触电极之熔合制程，使铍扩散至磷化镓层，同时利用铍渗入磷化镓造成之特殊组成，可形成不均匀之蚀刻阻挡，而在磷化镓表面形成粗化，我们发现480℃、10分钟的熔合制程，加上浸泡磷化镓蚀刻溶液6分钟，可将四元发光二极体之发光亮度由42 mcd 提升到50 mcd，经由此无光罩粗化制程可将亮度提升18%，明显提升磷化铝铟镓发光二极体之外部量子效率。

The optimized device process of p-n Alo.85Gao.15As/GaAs solar cells have been investigated. AuBe/Au and AuGeNi/Au were evaporated and metallized to form ohmic contacts of front grids and back electrodes, respectively. Heavily-doped GaAs cap layers were removed by the NH4OH:H202:H3P04:H20 selective etching solution.

分别采用真空蒸发AuBe/Au和AuGeNi/Au并合金化形成欧姆接触制作太阳电池正面栅线和背面电极；采用NH_4OH：H_2O_2：H_3PO_4：H_2O体系的选择性腐蚀液去除高掺杂的GaAs接触层；采用真空蒸发技术制备ZnS/MgF_2双层复合减反射膜。

If you jumper the 220 ohm, clip out the extra buffer transistor and connect the jfet signal coupling cap to the emitter of the input buffer, and change one resistor in the input buffer biasing circuit, you have a working TS9 in the TS10 case.

如果你跳了220欧姆，剪辑出额外的缓冲晶体管和连接场效应信号耦合帽来灌水的输入缓冲区改变一个电阻器的输入缓冲器偏置电路，你有一个工作ts9在ts10案件。

PART 1 UNIT 1 B Electrical and Electronic Engineering Basics A Electrical Networks ———————————— 3 Three-phase Circuits A The Operational Amplifier ——————————— 5 UNIT 2 B Transistors A Logical Variables and Flip-flop —————————— 8 UNIT 3 B Binary Number System A Power Semiconductor Devices —————————— 11 UNIT 4 B Power Electronic Converters A Types of DC Motors —————————————15 UNIT 5 B Closed-loop Control of DC Drivers A AC Machines ———————————————19 UNIT 6 B Induction Motor Drive A Electric Power System ————————————22 UNIT 7 B PART 2 UNIT 1 B Power System Automation Control Theory A The World of Control ————————————27 —————29 The Transfer Function and the Laplace Transformation UNIT 2 B A Stability and the Time Response ————————— 30 Steady State————————————————— 31 A The Root Locus ————————————— 32 ————— 33 UNIT 3 B The Frequency Response Methods: Nyquist Diagrams UNIT 4 A The Frequency Response Methods: Bode Piots ————— 34 B Nonlinear Control System 37 UNIT 5 A Introduction to Modern Control Theory B State Equations 40 38 UNIT 6 A Controllability, Observability, and Stability B Optimum Control Systems UNIT 7 A Conventional and Intelligent Control B Artificial Neural Network Computer Control Technology A Computer Structure and Function 42 B Fundamentals of Computer and Networks 43 44 PART 3 UNIT 1 UNIT 2 A Interfaces to External Signals and Devices B The Applications of Computers 46 UNIT 3 A PLC Overview B PACs for Industrial Control, the Future of Control UNIT 4 A Fundamentals of Single-chip Microcomputer 49 B Understanding DSP and Its Uses 1 UNIT 5 A A First Look at Embedded Systems B Embedded Systems Design Process Control A A Process Control System B 50 PART 4 UNIT 1 Fundamentals of Process Control 52 53 UNIT 2 A Sensors and Transmitters B Final Control Elements and Controllers UNIT 3 A P Controllers and PI Controllers B PID Controllers and Other Controllers UNIT 4 A Indicating Instruments B Control Panels Control Based on Network and Information A Automation Networking Application Areas B Evolution of Control System Architecture PART 5 UNIT 1 UNIT 2 A Fundamental Issues in Networked Control Systems B Stability of NCSs with Network-induced Delay UNIT 3 A Fundamentals of the Database System B Virtual Manufacturing—A Growing Trend in Automation UNIT 4 A Concepts of Computer Integrated Manufacturing B Enterprise Resources Planning and Beyond Synthetic Applications of Automatic Technology A Recent Advances and Future Trends in Electrical Machine Drivers B System Evolution in Intelligent Buildings PART 6 UNIT 1 UNIT 2 A Industrial Robot B A General Introduction to Pattern Recognition UNIT 3 A Renewable Energy B Electric Vehicles UNIT 1 A

电路 2 电路或电网络由以某种方式连接的电阻器，电感器和电容器等元件组成。如果网络不包含能源，如电池或发电机，那么就被称作无源网络。换句话说，如果存在一个或多个能源，那么组合的结果为有源网络。在研究电网络的特性时，我们感兴趣的是确定电路中的电压和电流。因为网络由无源电路元件组成，所以必须首先定义这些元件的电特性。就电阻来说，电压-电流的关系由欧姆定律给出，欧姆定律指出：电阻两端的电压等于电阻上流过的电流乘以电阻值。在数学上表达为： u=iR (1-1A-1)式中 u=电压，伏特；i =电流，安培；R =电阻，欧姆。纯电感电压由法拉第定律定义，法拉第定律指出：电感两端的电压正比于流过电感的电流随时间的变化率。因此可得到：U=Ldi/dt 式中 di/dt =电流变化率，安培/秒； L =感应系数，享利。电容两端建立的电压正比于电容两极板上积累的电荷 q 。因为电荷的积累可表示为电荷增量 dq 的和或积分，因此得到的等式为 u=，式中电容量 C 是与电压和电荷相关的比例常数。由定义可知，电流等于电荷随时间的变化率，可表示为 i = dq/dt。因此电荷增量 dq 等于电流乘以相应的时间增量，或 dq = i dt，那么等式(1-1A-3)可写为式中 C =电容量，法拉。

PART 1 Electrical and Electronic Engineering Basics UNIT 1 A Electrical Networks B Three-phase Circuits UNIT 2 A The Operational Amplifier ——————————— 5 B Transistors UNIT 3 A Logical Variables and Flip-flop —————————— 8 ———————————— 3 B Binary Number System UNIT 4 A Power Semiconductor Devices —————————— 11 B Power Electronic Converters UNIT 5 A Types of DC Motors —————————————15 B Closed-loop Control of DC Drivers UNIT 6 A AC Machines ———————————————19 B Induction Motor Drive UNIT 7 A Electric Power System ————————————22 B Power System Automation PART 2 Control Theory UNIT 1 A The World of Control ————————————27 B The Transfer Function and the Laplace Transformation UNIT 2 A B —————29 Stability and the Time Response ————————— 30 ————————————— 32 Steady State————————————————— 31 UNIT 3 A The Root Locus B The Frequency Response Methods: Nyquist Diagrams ————— 33 UNIT 4 A The Frequency Response Methods: Bode Piots ————— 34 B Nonlinear Control System 37 UNIT 5 A Introduction to Modern Control Theory B UNIT 6 State Equations 40 38 A Controllability, Observability, and Stability B Optimum Control Systems UNIT 7 A Conventional and Intelligent Control B Artificial Neural Network PART 3 UNIT 1 Computer Control Technology A Computer Structure and Function B 42 43 44 Fundamentals of Computer and Networks UNIT 2 A Interfaces to External Signals and Devices B The Applications of Computers 46 UNIT 3 A PLC Overview B PACs for Industrial Control, the Future of Control 1 UNIT 4 A Fundamentals of Single-chip Microcomputer B Understanding DSP and Its Uses 49 UNIT 5 A A First Look at Embedded Systems B Embedded Systems Design PART 4 UNIT 1 Process Control A A Process Control System 50 B Fundamentals of Process Control 53 52 UNIT 2 A Sensors and Transmitters B Final Control Elements and Controllers UNIT 3 A P Controllers and PI Controllers B PID Controllers and Other Controllers UNIT 4 A Indicating Instruments B Control Panels PART 5 UNIT 1 Control Based on Network and Information A Automation Networking Application Areas B Evolution of Control System Architecture UNIT 2 A Fundamental Issues in Networked Control Systems B Stability of NCSs with Network-induced Delay UNIT 3 A Fundamentals of the Database System B Virtual Manufacturing—A Growing Trend in Automation UNIT 4 A Concepts of Computer Integrated Manufacturing B Enterprise Resources Planning and Beyond PART 6 UNIT 1 Synthetic Applications of Automatic Technology A Recent Advances and Future Trends in Electrical Machine Drivers B System Evolution in Intelligent Buildings UNIT 2 A Industrial Robot B A General Introduction to Pattern Recognition UNIT 3 A Renewable Energy B Electric Vehicles 2 UNIT 1 A

电路 电路或电网络由以某种方式连接的电阻器，电感器和电容器等元件组成。如果网络不包含能源，如电池或发电机，那么就被称作无源网络。换句话说，如果存在一个或多个能源，那么组合的结果为有源网络。在研究电网络的特性时，我们感兴趣的是确定电路中的电压和电流。因为网络由无源电路元件组成，所以必须首先定义这些元件的电特性。就电阻来说，电压-电流的关系由欧姆定律给出，欧姆定律指出：电阻两端的电压等于电阻上流过的电流乘以电阻值。在数学上表达为： u=iR (1-1A-1)式中 u=电压，伏特；i =电流，安培；R =电阻，欧姆。纯电感电压由法拉第定律定义，法拉第定律指出：电感两端的电压正比于流过电感的电流随时间的变化率。因此可得到：U=Ldi/dt 式中 di/dt =电流变化率，安培/秒； L =感应系数，享利。电容两端建立的电压正比于电容两极板上积累的电荷 q 。因为电荷的积累可表示为电荷增量 dq 的和或积分，因此得到的等式为 u=，式中电容量 C 是与电压和电荷相关的比例常数。由定义可知，电流等于电荷随时间的变化率，可表示为 i = dq/dt。因此电荷增量 dq 等于电流乘以相应的时间增量，或 dq = i dt，那么等式(1-1A-3)可写为式中 C =电容量，法拉。

PART 1 Electrical and Electronic Engineering Basics UNIT 1 A UNIT 2 A UNIT 3 A UNIT 4 A UNIT 5 A UNIT 6 A UNIT 7 A Electrical Networks ———————————— 3 B Three-phase Circuits The Operational Amplifier ——————————— 5 Logical Variables and Flip-flop —————————— 8 Power Semiconductor Devices —————————— 11 Types of DC Motors —————————————15 AC Machines ———————————————19 Electric Power System ————————————22 B Transistors B Binary Number System B Power Electronic Converters B Closed-loop Control of DC Drivers B Induction Motor Drive B Power System Automation PART 2 Control Theory UNIT 1 A B UNIT 2 A UNIT 3 A UNIT 4 A The World of Control ————————————27 Stability and the Time Response ————————— 30 The Root Locus ————————————— 32 The Transfer Function and the Laplace Transformation —————29 B Steady State————————————————— 31 B The Frequency Response Methods: Nyquist Diagrams ————— 33 The Frequency Response Methods: Bode Piots ————— 34 B Nonlinear Control System 37 UNIT 5 A Introduction to Modern Control Theory B B B PART 3 B B B State Equations Optimum Control Systems Artificial Neural Network Computer Control Technology 42 43 44 Fundamentals of Computer and Networks The Applications of Computers 46 40 38 UNIT 6 A Controllability, Observability, and Stability UNIT 7 A Conventional and Intelligent Control UNIT 1 A Computer Structure and Function UNIT 2 A Interfaces to External Signals and Devices UNIT 3 A PLC Overview PACs for Industrial Control, the Future of Control 1 UNIT 4 A Fundamentals of Single-chip Microcomputer 49 B B PART 4 B B B B PART 5 B B B B PART 6 Understanding DSP and Its Uses Embedded Systems Design Process Control 50 52 53 Fundamentals of Process Control UNIT 5 A A First Look at Embedded Systems UNIT 1 A A Process Control System UNIT 2 A Sensors and Transmitters Final Control Elements and Controllers PID Controllers and Other Controllers Control Panels Control Based on Network and Information Evolution of Control System Architecture Stability of NCSs with Network-induced Delay Virtual Manufacturing—A Growing Trend in Automation Enterprise Resources Planning and Beyond Synthetic Applications of Automatic Technology UNIT 3 A P Controllers and PI Controllers UNIT 4 A Indicating Instruments UNIT 1 A Automation Networking Application Areas UNIT 2 A Fundamental Issues in Networked Control Systems UNIT 3 A Fundamentals of the Database System UNIT 4 A Concepts of Computer Integrated Manufacturing UNIT 1 A Recent Advances and Future Trends in Electrical Machine Drivers B B B System Evolution in Intelligent Buildings A General Introduction to Pattern Recognition Electric Vehicles UNIT 2 A Industrial Robot UNIT 3 A Renewable Energy 2 UNIT 1 A

电路 电路或电网络由以某种方式连接的电阻器，电感器和电容器等元件组成。如果网络不包含能源，如电池或发电机，那么就被称作无源网络。换句话说，如果存在一个或多个能源，那么组合的结果为有源网络。在研究电网络的特性时，我们感兴趣的是确定电路中的电压和电流。因为网络由无源电路元件组成，所以必须首先定义这些元件的电特性。就电阻来说，电压-电流的关系由欧姆定律给出，欧姆定律指出：电阻两端的电压等于电阻上流过的电流乘以电阻值。在数学上表达为： u=iR (1-1A-1)式中 u=电压，伏特；i =电流，安培；R =电阻，欧姆。纯电感电压由法拉第定律定义，法拉第定律指出：电感两端的电压正比于流过电感的电流随时间的变化率。因此可得到：U=Ldi/dt 式中 di/dt =电流变化率，安培/秒； L =感应系数，享利。电容两端建立的电压正比于电容两极板上积累的电荷 q 。因为电荷的积累可表示为电荷增量 dq 的和或积分，因此得到的等式为 u=，式中电容量 C 是与电压和电荷相关的比例常数。由定义可知，电流等于电荷随时间的变化率，可表示为 i = dq/dt。因此电荷增量 dq 等于电流乘以相应的时间增量，或 dq = i dt，那么等式(1-1A-3)可写为式中 C =电容量，法拉。

Meanwhile, the accurate mask alignment between the active layer on the bottom glass and the black matrix on the top glass and the choice of low-reflectivity black matrix material in conventional technology are also omitted.

并利用淀积欧姆接触层n〓a-Si：H和金属薄膜时沉积在SiN〓保护层上的n〓a-Si：H和金属薄膜作遮光黑层，省去了传统方法中上玻璃基板的黑矩阵与下玻璃基板TFT有源层沟道之间苛刻的对版工艺，并避免了传统黑矩阵制作工艺中对低反射率黑层材料的需求。

This paper introduces the designing and using of a new type Ohmmeter based on the way of bridge circuit according to the theory of electronics without galvanometer.

根据电桥法测量电阻的基本思想，结合电子学理论，设计一种毋须检流计的新型欧姆表，并介绍它的使用。

In order to response Chinese marketing changing and developing rapidly, OMRON and BTU will intensify co-operation in China to offer more professional and excellent quality products for Chinese electronic semiconductor industry.

为了应对中国市场的不断变化和飞速增长，欧姆龙和BTU进一步深化在中国的合作，为不断发展的中国电子半导体行业提供更为专业和优质的产品。

The centimeter-gram-second electromagnetic unit of current equal to ten amperes.

电流的单位是安培，电阻的单位是欧姆，电压的单位是伏特。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。