次主

The experiment results prove that the boiler coking is largely reduced and the temperature difference of two sides of horizontal gas-pass is very small, when the 330MW boiler operate, the pressure of primary hot air parison is controlled beyond 12.0～12.5KPa, the O2 content of air pheheater is controlled about 3.0%, the door of OFA is opened to 30%, the buffle of the inner secondary air sleeve is adjusted to the minimum, the outer secondary air swirling strength and the baffle of the outer secondary air sleeve is regulated to the maximum and the outlet temperature of pulvervised mill is kept in 70℃.

试验结果表明，330MW运行时，一次热风母管压力控制在12.0～12.5kPa以上、空气预热器实际氧量控制在3.0％左右、燃尽风门开至30％、内二次风量套筒挡板调整在最小、外二次旋流强度和外二次风套筒挡板调整到最大、磨煤机出口温度维持在70℃，此时锅炉结焦大幅度减轻，水平烟道两侧烟温差非常小。优化试验完成后，进行了单烧灵武烟煤对比，结果是：掺烧高灰熔点的银北煤后，炉膛结焦大幅度减轻，锅炉过热器减温水量较小，主蒸汽压力易提高，带负荷能力正常；再热器烟气挡板开度较大、减温水量较小；风机电耗较小。

Moreover the influence of consolidation pressure on the coefficient of secondary consolidation, the effect of load increment ratio on secondary deformation and the pore water pressure at the latter stage of consolidation are investigated.

基于对这些试验资料的分析，提出了一种新的主、次固结变形划分法，同时还探讨了固结应力和应力比对次固结系数的影响、固结后期的孔隙水压力和荷载增量比对次固结变形比例的影响。

To wipe out the curse of blasphemy, which has increased beyond measure towards a supreme contempt for the divine name and for the saints, we rule and ordain that whoever curses God openly and publicly and, by insulting and offensive language, has expressly blasphemed our lord Jesus Christ or the glorious virgin Mary, his mother, if he has held a public office or jurisdiction, he is to lose three months' emoluments of his said office for the first and second offence, and if he has committed the fault a third time, he is automatically deprived of his post.

要彻底消灭这个诅咒的亵渎，这增加了不可估量实现最高蔑视神圣的名字和圣人，我们的规则和任命，无论谁咒骂上帝公开，并通过侮辱和攻击性语言，已明确地亵渎我们的主耶稣或圣母玛利亚的光荣，他的母亲，如果他曾担任公职或管辖范围内，他将失去3个月的薪酬，他说，办公室第一次和第二次犯罪，如果他已承诺的第三次故障，他将自动被剥夺一切职务。

The first approximate solution for amplitude frequency response curve of the primary resonance of the system has hardening characteristic.

分析一次近似解、二次近似解的特点，指出系统主共振的一次近似解的幅频响应曲线表现为硬刚度特性；二次近似解的幅频响应曲线表现为软刚度特性。

Each injection of a proton, it caused a decline in H is called a substorm, magnetic storm main phase is a series of substorm occurred results.

每注入一次质子，就造成H下降一次，称为一次亚暴，磁暴主相是一连串亚暴连续发生的结果。

The characteristic vector of the real symmetric matrix should be found out, which is orthogonalized and normalized to a standard orthogonal base and is used as row vector to construct the transformation matrix P, so the P~(-1)AP can be made into diagonal matrix.

实对称矩阵A经相似变换P-1AP可化为对角矩阵，在x =Py 下，不一定能化A的二次型为标准型；应寻求对称矩阵A的特征向量，将其正交化并单位化作为标准正交基，作为列向量构造变换矩阵P，可使P-1AP=Λ为对角阵，在x =Py 下，要将二次型化为标准型，且二次项系数即为对角阵Λ主对角线上元素。

It involves a spherical primary mirror and the secondary mirror with profile given by computer.lt is not necessary for the new optical system to obtain the on-axis solar image,so the secondary mirror may have a simpler profile.

一种由球面主镜和由计算机算出曲面型线的二次镜组成的新型二次反射聚光系统，可以减少制造困难，当这种光学系统用于太阳能聚光器时，由于不需要得到轴上的太阳像，其二次镜型线可更为简单。

In order to solve the current differential protection's maloperation, the combined harmonic blocking criteria and the criteria based on the trace of action point are proposed.

电流互感器发生暂态饱和时，二次电流中的谐波主要是2次谐波，3次谐波含量很少。

The objectives of this paper were to investigate the simulation and design of continuous multiple-station rolling forming process for a U-Section Steel Bar by CAE software-DEFORMTM Due to the limitation of elements number using a short strip 120mm went through all the stations to simulate the real continuous rolling forming on factory The roller gap was fixed as 0 30mm roll speed was 20 rad/sec and progressive angles were all equal for each rolling process which were the formed angle divided by by the number of station Three rolling processes were selected with 6 9 and 12 stations respectively During simulation processes two cases occurred Case A the strip was through a single station Case B the strip across two stations Because the strip laterals side was stretched and twisted during the process The model of case B closer to the practical process than case A and the calculated stress and strain on the tip of U section for case A were lower than these for case B by up to 15% From the result of case B for each process the stress for 12-station process was smallest 9-station process second and 6-station process next Because less-station can save larger cost and forming time but the bigger stress and strain for 6-station caused wrinkles on lateral sides not found on 9-station and 12-station Therefore 9-station process was a more suitable design than 12-station process smaller stretched and twisted and stress The progressive angles for 12-station was 7 5?

本文主要是以DEFORMTM有限元素软体模拟U型钢片连续道次成型与单一道次成型以确认单一道次模拟的是否可取代连续道次模拟之研究。因DEFORMTM 软体对於网格元素上的限制故使用较短素材120mm通过所有的成型站以模拟工厂实际连续成形方法。辊轮间隙固定为0 3mm；辊轮转速为20 rad/sec；弯曲角度的方法为将成型角度平均除以成型站数。有三种辊轮成型方式被选择分别为6站，9站，与12站。在模拟的过程中有两种现象会产生 Case A，素材通过单一成型站。Case B，素材会通过两个成型站。因为在模拟过程中素材的两端会有拉应力与扭力。Case B的模拟比Case A像实际的制程，并计算应力与应变在U型断面的Tip部中可发现Case A比Case B低约15%。从Case B的每站的结果可以得知，12站的成型应力最小，9站次之，6站最后。

Three times a year, then, every male among you shall appear before the LORD, your God, in the place which he chooses: at the feast of Unleavened Bread, at the feast of Weeks, and at the feast of Booths.

每年三次，即在无酵节、七七节和帐棚节，你所有的男子都应到上主所选的地方去，朝拜上主你的天主；但不要空手出现在上主面前

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。