模转换

After converting ,filtering and magnifying for four kinds signal produced by biochemistry enzyme （blood sugar ,lactic acid,cholesterol and acetone body）,the results are converted separately by AID converter of AdμC812, and then displayed on LCD.

送到AdμC812的四路A／D转换口进行模数转移，然后经过相应的运算、处理后在液晶显示器上显示出来。同时还能对测得的结果进行一些常规的实时诊断。

So digitalizing analog signal is the trend of information technology, in which Analog to Digital converter plays an important role.

所以模拟信号数字化是信息技术的发展趋势，而模数转换器在其中扮演着重要的角色。

However, in the real world, the performance of an analog to digital converter is constrained by many factors.

但是，在真实世界中，模数转换器的性能受到许多因素制约。

Analog to Digital Converter is the interface of analog and digital circuit, its use is very extensive.

模数转换器是模拟电路和数字电路的接口，其用途非常广泛。

One of these constraining factors is self generated noise within the analog to digital converter.

这些制约因素之一是在模数转换器内自生的噪声。

The well-grown hMSCs of the first to second generation were chosen to perform the record and analysis with whole cell patch clamp technology, Type PC-IIB patch clamp amplifier （developed by Huazhong University of Technology was adopted in this experiment）.

实验采用PC-IIB型膜片钳放大器，由计算机发出指令经数字量数据／模拟量数据转换经放大器输出到细胞，细胞信号由放大器放大再经模／数转换后记录到计算机，保存在数字硬盘上供分析调读，记录与分析软件为IBBClamp，采样间隔100μs。

The graduation design is based on single chip microcomputer intelligent design of a power source, hardware design is the main task of the circuit design, battery, the three groups of different size power design, system design, manostat ADC0809 adc design, display design, the watchdog circuit module design, 3-8 decoder circuit design, AT89C51 basic circuit design, 74LS161 prescaler design and auxiliary circuit design, Software design task is: initialize program design, and key process design, charge control program design, A/D conversion program design, over-current protection program design, display design program.

本次毕业设计注意是设计一个基于单片机的智能电源，硬件设计的主要任务是：蓄电池充电电路的设计、三组不同大小的电源设计、系统稳压电源设计、ADC0809模数转换电路设计、看门狗电路设计、显示模块设计、3-8译码电路设计、AT89C51基本工作电路设计、74LS161分频器设计和辅助电路设计；软件设计的任务是：初始化程序设计、按键程序设计、充放电控制程序设计、A/D转换程序设计、过流保护程序设计、显示程序设计。

The environment light intensity is converted into a high or a low electric level of RA2 which is one of the input ports of single chip microcomputer through a photoresistance MG44-2.The AD module will sample and the result will be stored in the work register then compared with a prestablished quantity.

基于PIC16F877A单片机的电子时间引信LCD背光控制，将环境光强度通过MG44-2光敏电阻器转换为单片机输入端口RA2上的电平高低，经模数转换模块进行采样，其结果存入工作寄存器，并与预先设定值相比较。

In this design, hardware circuit adopts liquid crystal screen and program sensor keyboard as interactive interface, 96 single-chip as chief controller, analog multi-circuit switch as transmission signal. To improve conversion accuracy, I also bond an analog to digital converter%26mdash;AD1674, so the programs mainly contain the display program design of the LCD module, the key-board control program and cyclical monitoring of various parameters and so on.

本文的硬件电路采用液晶显示屏和触摸式键盘作为人机交互界面，用80C196KB作为主控制器，用模拟多路开关传输信号，并且为了提高转换精度，外接了模数转换器AD1674，所以本设计的程序主要包括液晶显示程序、键盘管理程序、控制巡回采样等模块。

In this study, we used poly L-latcide, poly DL-latcide-co-glycolide 75:25 (PLGA7525) and poly DL-latcide-co-glycolide 50:50 (PLGA5050) during citric acid inducing ammonium bicarbonate gas forming process to form porous polymer film, and rolled the porous polymer film to make nerve conduits with pores and multi-layered. Electron Spectroscopy for Chemical Analyzer and Attenuated Total Reflectance – Fourier-Transform Infrared Spectrometer were employed for determining elements' functionabilities and chemical compounds. Charge Coupled Device camera and Scanning Electron Microscope were employed for macroscopic and microscopic morphologies and structural observation. Differential Scanning Calorimetry was employed for measuring glass-transition temperature. Nano-indentation system was employed for measuring elastic modulus and hardness. Biodegradation and water absorption ratios were measured to analyze their chemical properties and SEM was employed for microscopic morphology of the tested nerve conduit.

本研究将以聚乳酸、聚乳酸-聚甘醇酸共聚合物（75：25）、聚乳酸-聚甘醇酸共聚合物（50：50）做为研究材料，以柠檬酸诱发碳酸氢铵发泡之气泡成型法制作具有相连通孔隙之高分子薄膜，再将高分子薄膜卷制成特殊多层的导管，制作具有多层孔隙之新型神经再生导管，以电子能谱化学分析及减弱式全反射-傅立叶转换红外线光谱分析进行成份分析及化学元素测定；以电荷耦合元件摄影机、扫瞄式电子显微镜进行多层孔隙型神经导管巨观及微观形态结构观察；以示差扫瞄热量量测分析玻璃转换温度、奈米三维量测弹性模数及硬度；以及进行降解性质测定，并以扫瞄式电子显微镜进行降解后之导管微观结构形态观察。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。