模板

How to dynamically determine the template to use.

如何动态确定要使用的模板。

Moreover, the size of nanorods changes with the concentration of the precursor SnCl4. We also fabricate dysprosium hydroxide by means of the similar method.

我们利用相同的路线制备出了Dy3纳米管，合成过程中，聚乙二醇充当了模板剂，反应在180°C水热条件下完成。

Through customizing 3D template and 2D drawing template, Improving the efficiency of using Pro/Engineer modeling greatly, bringing the result that gets twice the result with half the effort to the establishment of the 2D drawing and BOM too.

通过三维模板及二维工程图的定制，大大提高了使用Pro/Engineer建模的效率，也给二维工程图及BOM的创建带来事半功倍的效果。

Further, the influence of elution temperature and sample load on the selectivity of polymers was investigated in detail.

MIPs高度的底物选择性主要来源于MIPs中识别位点与模板分子在空间和功能基团上的匹配。

METHODS: Tum5 gene was amplified from plasmid pSPORT1Sfi by PCR technique and subcloned into the expression plasmid of lentiviral vector, pGCFU, to generate the lentiviral expression vector, pGCFUTum5. The correct Tum5 gene was confirmed by endoenzyme digestion and sequencing. Recombinant lentiviruses were produced by 293T cells following the cotransfection of pGCFU Tum5 and packaging plasmids-pHelper1.0and pHelper2.0. The resulting recombinant lentiviruses (GCFUTum5) which carried Tum5 and EGFPgene were then used to infect human umbilical vein endothelial cells.

采用PCR技术从含有tumstatin基因的质粒克隆模板 pSPORT1Sfi钓取Tum5基因，并将基因克隆到慢病毒载体表达质粒pGCFU中，构建慢病毒载体表达质粒pGCFUTum5，通过酶切、测序验证Tum5基因后，将pGCFUTum5质粒和包装质粒pHelper1.0，pHelper2.0共同转染人胚胎肾上皮细胞系293T细胞，获得携带Tum5基因和EGFP基因的重组慢病毒GCFUTum5，并转染靶细胞人脐静脉血管内皮细胞。

Dimensional hype, of course this method is good without the method above perhaps, but have long sex quite, as far as possible the beautiful point that makes the vacuum, of course FLASH, dimensional module, dimensional pattern plate, belle picture, individual character autograph is waited a moment, what should get the space is super and flowery, next the picture adds watermark, and contain website link, catch even if go much space leaves a message, remember wanting the font of enlarge space address in leave a message!

5，空间炒作，当然这个方法也许没有上面的方法好，但是比较具有长久性，尽可能的把空间做的漂亮点，当然FLASH，空间模块，空间模板，美女图片，个性签名等等，要把空间弄的超级绚丽，然后图片加上水印，并且带有网站链接，接着就是去大量的空间留言，记住在留言中要放大空间地址的字体哦！

It is found that organic nanotubes from keto-enol isomeric dibenzoylmethane with different diameters show unique size dependent properties according to our experimental and calculated results. With the diameters of the nanotubes decreasing, the enol isomers of DBM molecules increased, the intensity of the fluorescence emission enhanced.

制备了平面稠环分子苝的纳米管，发现纳米管的形成机制源于模板孔洞的高长径比及溶液在高表面能基体上的自发铺展过程，苝层层沉积从而形成纳米管，苝分子头对尾的聚集体是形成纳米管的主要成份。

III For constructing the expression vector of a fusion protein and obtain a target protein with full identity on aa sequence of a natural 13- 1,3-1 ,4-glucanase, with the recombined plasmid DNA harbouring the target gene as template, the primers designed with restriction sites for both terminals and enterokinase recognition site, followed by PCR amplification, was induced to the target gene.

为构建融合蛋白表达载体和获得与天然蛋白质序列完全一致的目的蛋白，以含有目的基因的重组质粒DNA为模板，设计引物时加入两端酶切位点及肠激酶裂解位点，通过PCR扩增引入目的基因中，测序结果表明接头和读框正确。

The designer did not enwrap columns with stone or wood , but just exposed the original concrete with imprints by construction using wood moulding board .

设计人没有将柱子包贴石材或木材，而是用木模板清水混凝土，显现水泥本色。

Design of irregular template based on the concentric equipotential line of target contour,combined with the projection,can quicly and efficiently realize automatic identification and position of irregular images by the computer.

针对工业自动装配产品过程中异形工件出现旋转后的定位问题，提出一种新的异形目标识别方法，设计基于目标轮廓的同心等势线异形模板，并结合圆投影方法，能快速有效地实现计算机对异形目标的自动识别与定位。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。