模数的

Low power, low cost and noise free is a hot research on the field of analog-to-digital converter.

如何使模数转换器既拥有较强的抗干扰能力，同时达到低功耗的要求，越来越成为模拟集成电路研究的热点和难点。

With the explosive development of communication and digital signal processing technology, an analog-to-digital converter, as an interface between analog signal and digital signal is necessary.

随着通信技术和数字信号处理技术的快速发展，作为模拟信号与数字信号界面的模数转换器得到了越来越广泛的应用。

The error of output signal is caused by clock shaking in the analog-to-digital converter, which can affect the succeeding signal processing.

模数转换器的时钟抖动引起输出信号的误差，该误差会影响后继的数字信号处理。

Finally, the mod includes specific start dates for boats in certain flotillas.

最后，模数为在某些小舰队的小船包括具体的开始日期。

These efforts have not found general acceptance, however, although good results have been achieved through the repetition of some dimension ( for example , a module that is half the diameter of a column) throughout a design.

然而，尽管在整个设计中通过重复某种模数（如，一个柱子的半径为一个单元）已经获得良好的结果，但所有这些努力尚未被普遍认可。

In order to resolve the practical problem about measuring hobs with bigger modulus, a new method is put forward by which the circular adjacent pitch error and accumulated pitch error of hobs can be measured on the grinder.

针对大模数滚刀测量存在的实际问题，提出一种在磨床上测量滚刀容屑槽相邻周节误差和周节累积误差的新方法，并给出了测量实例。

The company worked for research and development of motorcycle gear and automobile gear, and become a lead in manufacture mid modulus gear and small modulus gear.

自公司建立以来就致力于各型摩托车齿轮和汽车齿轮的研发与制造，并逐渐成长为中小模数齿轮生产厂家的领先企业。

Stage 3: When the load was increased beyond P1 (greater than 6000 lb, 26.7KN), tensile stresses in concrete at the tension zone increased until they were greater than the modulus of rupture fc, and cracks developed.

阶段3：当装载在P1 (大于6000磅之外被增加了， 26.7KN)，张应力在混凝土在紧张区域增加了，直到他们大于破裂fc的模数，并且被开发的镇压。

In this design, hardware circuit adopts liquid crystal screen and program sensor keyboard as interactive interface, 96 single-chip as chief controller, analog multi-circuit switch as transmission signal. To improve conversion accuracy, I also bond an analog to digital converter%26mdash;AD1674, so the programs mainly contain the display program design of the LCD module, the key-board control program and cyclical monitoring of various parameters and so on.

本文的硬件电路采用液晶显示屏和触摸式键盘作为人机交互界面，用80C196KB作为主控制器，用模拟多路开关传输信号，并且为了提高转换精度，外接了模数转换器AD1674，所以本设计的程序主要包括液晶显示程序、键盘管理程序、控制巡回采样等模块。

Then came Le Corbusier's Modular, defining parameters that are also applied in the field of design.

最后是柯布西耶的&模数&，确定了同样可以适用到设计领域中的各种参数。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。