模数

Pitch circle diameter: d = mz = 3X12 = 36 Tooth crown heights: ha = m (f0 + x)= 3X (l +0.5)= 4.5 Tooth High: hf = m (f0 + cx)= 3X (l +0.25-0.5)= 2.25 Tooth full height: h = ha + hf = 4.5 +2.25 = 6.75 Addendum circle Chemical pumps diameter: Da = d +2 ha = 36 +2 X4.5 = 45 Fixed string tooth thickness: Sxn = m (π/ 2 * cos2a + xsin2a)= 3X (1.387 +0.6428 X0.5)= 5.125 Fixed string of high gear tooth thickness measurement: hxn = m (π/ 8 * sin2a + xsin2a)= 3X (0.7476X0.117X0.5)= 2.42 Modulus coefficient x0.5 m3 O20 ° pressure angle tooth thickness Sxn5.12 fixed string Addendum Coefficient string f1 fixed gear tooth thickness measurement most high hxn2.42 Teeth z12 2, shaft wear and tear maintenance: Axis gear pump wear is mainly because with the support roller shaft at both ends between the friction and wear, so that smaller shaft diameter.

分度圆直径：d=mz=3X12=36 齿顶高：ha=m（f0+x）=3X（l+0.5）=4.5 齿根高：hf=m（f0+c-x）=3X（l+0.25-0.5）=2.25 齿全高：h=ha+hf=4.5+2.25=6.75 齿顶圆直径：Da=d+2ha=36+2X4.5=45 固定弦齿厚：Sxn=m（π/2*cos2a+xsin2a）=3X（1.387+0.6428X0.5）=5.125 固定弦齿厚测量用齿高：hxn=m（π/8*sin2a+xsin2a）=3X（0.7476X0.117X0.5）=2.42 模数m3变位系数x0.5 齿形角o20°固定弦齿厚Sxn5.12 齿顶高系数f1固定弦齿厚测最齿高hxn2.42 齿数z12 2、轴的磨损维修：齿轮泵中轴的磨损主要是因为轴两端与支撑滚针间的摩擦磨损，使轴径变小。

Error analysis of digital instruments on their characteristic parts including sample/holder circuit error and analogue/digital convector error was reviewed in this paper. With the help of some examples and data tables, error origins and the synthetic method were discussed.

评价了数显仪特征部分误差分析方法，包括：采样／保持电路、模数转换单元的误差，并通过典型例子和列表数据分析了多种误差源及其综合计算方法。

The new kind of transmission theory introduced in this article has been applied for patent (the application number is 200410012992.6) Some fundamental theory of the end face harmonic gear drive of oscillating teeth is investigated in this paper, which can benefit the design of the product and the popularization of the patent.

这种新型的传动装置属于空间的活齿传动机构，可以从根本上克服传统的径向谐波齿轮传动中柔轮的变形与其承载能力之间的矛盾，并可增加同时啮合的齿数，加大齿轮的模数，从而可以在保留径向谐波齿轮传动所有优点的基础上，使其所传递的功率增加数十倍。

Considering the problems of spurgear precise plastic forming, such as high deformation resistance, poor flowability and especial hardness to fill cant of gear, technological plan was developed based on precise plastic forming technique, successive control principle and consecutive local deformation theory. Moreover, structures of the rolling preform die and the die with up and down wellrounded forcer for stamping-extrusion and bulge-extrusion combining forming were designed too.

因此本文的主要研究内容和结果如下：本文以某种直齿轮：模数m＝2，齿数z＝20，压力角α＝200，变位系数x＝0为对象，针对直齿轮精密塑性成形变形抗力大，流动性差，特别是成形中齿轮角隅部分更加难以充满问题，基于精密塑性成形技术、逐次控制原理以及连续局部变形原理提出了"直齿轮滚轧制坯－镦挤、胀挤复合精成形"的工艺方案，设计了滚轧制坯的模具结构和上下冲头带圆角的镦挤、胀挤复合精成形的模具结构。

Clocks use modular arithmetic with modulus 12,so 4 hours after 9 o'clock is 1 o'clock.

时钟使用模数12作为模算术，因此9点钟以后过四个小时是1点钟

Inthe paper, the blind inspection is executed by using modular arithmetic, namely, modulus 2arithmetic.(The result is 0 or 1). A algorithm with high transparency and robustness is realizedby smartly combining this arithmetic with binary chaotic sequence.

文中利用模数运算实现了音频水印的盲检测，即利用模2 运算，模2 取余(所得结果为0 或1)，很巧妙地将这种运算与二值化的混沌水印序列相结合，实现了一种不可感知度高，嵌入量大的高鲁棒性水印算法。

Circle with a vernier caliper, and then calculate the number of teeth

测量齿轮先用游标卡尺测量齿轮的齿顶圆直径，再数齿数，然后计算齿轮模数。

The thesis discusses three eigenvalues individually and explains the pressure wave propagation of three modes, includes wave speed, wave decay and energy distribution. Since the elastic potential energy occupies more than 98% of mechanical energy in the arteries, which is larger than 2% of kinetic energy of flowing blood. Else join elastic wall and wall of managing having a viscid condition to analysis .

本文将个别讨论此三组特徵值，来说明三组压力波的传递模态，其中包括波速，以及波的衰减；由於在动脉的能量分布中，由管壁振动的弹性位能占了98%，远超过血液本身流动的2%，再加上管的弹性模数和管壁的黏滞性再来讨论此三组模态，个别在弹性管的能量分布。

Introduces a new technology for hobbing small module and fewer teethed gear with the usage of the transmission chain of Y631K spline shaft milling machine by adding the number of index change gears.

介绍利用Y631K 花键轴铣床传动链，适当增加分度挂轮数，滚切小模数、少齿数齿轮轴的加工技术。

This research applies the micro forming process with other mass production techniques to construct the key components of the micro/meso gear transmission. The final prototype is the planetary gear transmission with outer diameter 6mm and gear module less than 0.15mm developing in 3 years. The purposes and developing technologies of this project are as follows: 1. setting up the design and analysis of parts and system; 2. the mold design of gear and planet plate; 3. assembly modules of planetary gear train; 4. inspection of gear profile and gear train; and 5. heat treatment of micro parts.

本研究将以精微成形技术搭配其他量产制程，逐步开发微型减速机内的所有关键零件，预计在3年内最终完成外径≦ψ6mm、齿轮模数m≦0.12mm之的行星式齿轮减速机的开发，研发目标包含有微型传动系统结构/机构与零组件设计分析技术，试量产型精微行星/太阳齿轮、传动盘、环齿轮等原型件模具设计与开发，行星臂、太阳齿轮、行星齿轮与环齿轮等组装模组技术，微型齿轮齿形及相关微型齿轮箱检测技术，以及精微元件热处理技术等关键技术。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。