模数

Through analyzing the temperature field and stress field of typical steel castings some casting parameters as modulus, the distance of feeding head, cold iron are validated and modified, which is in accordance with the production-lines.

通过选取典型的铸钢件，采用实验的方法，对温度场、应力场、模数、冒口补缩距离、外冷铁等铸造工艺参数进行验证并加以修改，使其符合生产实际。

Finally, the mod includes specific start dates for boats in certain flotillas.

最后，模数为在某些小舰队的小船包括具体的开始日期。

These efforts have not found general acceptance, however, although good results have been achieved through the repetition of some dimension ( for example , a module that is half the diameter of a column) throughout a design.

然而，尽管在整个设计中通过重复某种模数（如，一个柱子的半径为一个单元）已经获得良好的结果，但所有这些努力尚未被普遍认可。

To solve the problem of inline measuring hobs with bigger modulus in practice production,an inline measuring system for the circular pitch error of hobs is introduced.

为了解决实际生产中大模数滚刀的在线测量，提出一种滚刀容屑槽周节误差测量系统。

In order to resolve the practical problem about measuring hobs with bigger modulus, a new method is put forward by which the circular adjacent pitch error and accumulated pitch error of hobs can be measured on the grinder.

针对大模数滚刀测量存在的实际问题，提出一种在磨床上测量滚刀容屑槽相邻周节误差和周节累积误差的新方法，并给出了测量实例。

Electronic current transformer ; virtual instrument ; Rogowski coil ; A/D transformation

电子式电流互感器；虚拟仪器； Rogowski线圈；模数转换

On the basis of analyzing and calculating transverse tooth profile for geometry, the symmetry line and tip arc of transverse tooth profile for a teeth of gear were defined and it also be drawed out.

由于渐开线圆柱齿轮的端面齿廓为渐开线，而且轮齿的厚度与齿轮的模数相关，所以用AutoCAD建立渐开线圆柱齿轮的三维模型十分困难。

If the bevel gear used in the processing module mid-point of the standard spur gear tooth milling cutter with big-deep into the alveolar knife milling, then the big-toothed on the "fat", little-endian tooth on the "thin."

如果在加工时采用伞齿轮中点模数的标准正齿轮铣刀以大端齿深将齿槽一刀铣成，那么大端齿形就&肥&，小端齿形就&瘦&。

The company worked for research and development of motorcycle gear and automobile gear, and become a lead in manufacture mid modulus gear and small modulus gear.

自公司建立以来就致力于各型摩托车齿轮和汽车齿轮的研发与制造，并逐渐成长为中小模数齿轮生产厂家的领先企业。

Most electronics steelyards with 1:3,000 or 1:10,000 resolutions output to endly weigh a value and use a 12 bits~the mold of the 14 bits count the conversion machine very easily satisfy a request.

大多数电子秤是以1：3，000或1：10，000的分辨率输出最终的称重值，使用12 bit~14 bit的模数转换器很容易满足要求。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。