模态的

First, one. analyzes the eigenstates-from reachable sets and seeks the one which the target state belongs to. Then using the Grover iteration to amplify the probability amplitude of the desired eigenstate (the modul square of which is the probability of the corresponding eigenstate that the system will collapse to when it is measured). By measuring, the system will then collapse to the desired eigenstate with a probability of almost unity. Finally, one can use the admissible control to drive the system from the eigenstate to the target state.

该策略的核心思想是对本征态能控的系统，通过分析控制目标态与本征态的关系，寻找给定目标态所属的本征态可达集，然后利用量子非结构化搜索的Grover算法，将任意给定的系统初始态经过一定次数的Grover迭代，放大该本征态所对应的概率幅(概率幅的模方对应测量时波函数塌缩到对应本征态的概率)，然后对迭代后的态进行一次测量操作，使系统以接近1的概率塌缩到所需的本征态(前面分析得到的本征态可达集所对应的本征态)，最后用容许的控制将系统从该本征态控制到期望的目标态。

For the different property between signal and noise in the intrinsic mode function domain, IMFs product detector is proposed. Under the condition of low SNR and the unknown distribution of noise, Simulation shows that IMFs product detector is superior to Teager energy operator detector.

利用信号和噪声在固有模态函数域中有不同的性态表现，提出了一种固有模态函数积检测器，在低信噪比和背景噪声分布未知条件下，IMF积检测器优于Teager能量算子检测器。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work.Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。2。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work. Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted. It was found in our drop tests that the root cause of lead-free solder joints under drop impact was the combined effect of mechanical shock and PCB bending vibration.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。

The simulation results of liquid propellant rocket engine demonstrate that modal interval analysis is effective to complex dynamic systems.

通过对某泵压式液体火箭发动机稳态工作过程的模态区间仿真计算，证明模态区间分析方法对复杂动态系统建模仿真是有效的。

The PZT plates were polarized in thickness direction. By using the deformation in the plane perpendicular to the direction of polarization, the rotation around Z axis was generated when the torsional vibration around Z axis mode was excited. And the rotation around X axis or Y axis was generated by combining the longitudinal vibration mode and the bending vibtration mode.

利用压电陶瓷在垂直极化方向平面内的变形，激励定子绕Z轴的扭转振动模态，实现转子绕Z轴的转动；激励在定子中固有频率接近、振动方向相垂直的伸缩振动模态和弯曲振动模态，并通过振动的叠加使定子末端质点产生绕X轴或者Y轴的椭圆运动，实现转子绕水平轴的转动。

In the part of the vibration experiments and analysis, firstly, used the simple-beam theory to estimate the natural frequency of the beam of the 20-headed computerized embroidery machine.secondly, measured the beam of its low rank natural frequency, the beams horizontal vibrating acceleration amplitude, speed amplitude and the displacement amplitude in different rev and different turn parts. Found that it is sympathetic vibration, which bring on the thread-broken rate rise rapidly. On this base, established the finite element analysis modle of the vibrating beam, and took on hamonic analysis and modal analysis with the mold. The rusult of test and analysis offer the basis for farther improvement of the computerized embroidery machine.

振动分析部分，首先由简单梁理论出发，对横梁的固有频率进行估算；接着通过测振仪器对20头电脑刺绣机横梁进行了试验模态分析和不同工况振动测试；获得了横梁前四阶固有频率和模态振型，以及在不同工作转速、不同回转部件下横梁振动的加速度幅值、速度幅值和位移幅值；找到了横梁振动加剧的原因——共振；在此基础上建立了符合实际情况的横梁有限元模型，对模型进行了模态和谐响应计算，证实了模型的可靠性，为下一步的改进设计提供了依据。

Thirdly, based on the continuum model, the natural modes of undamped complex framed structures are proved to be orthogonal with each other in a generalized sense. This leads to an alternative method for transient response analysis of undamped framed structures via the expansion of normal modes.

再次，基于MRRM列式，从连续模型的角度证明无阻尼复杂框架结构的固有模态具有正交性，并以此为基础构造模态叠加法来求解无阻尼复杂框架结构的瞬态响应。

With the fluid-solid coupling of train oil tank clue to train speed increase, the fluid-solid coupling modal analysis of G70B oil tank is calculated by NSYS. The finite element model of fluid-solid coupling system is set up. The fluid-solid coupling modal analysis of G70B oil tank is done for light oil tank train under different kinds of loads and its natural frequency and modal shapes are obtained.

针对列车油罐因列车提速导致液固耦合作用突出的问题，运用ANSYS软件对轻型油罐车G70B型罐体的液固辐合模态响应进行实例分析和计算；建立车载油罐的液固辐合系统有限元模型；对轻型油罐车G70B型罐体进行在不同贮液比时的液固福合模态分析，得出固有频率和模态振型图。

The modal testing measures the frequency call function of test points on scatter-gun and recognizes the step modal parameters by single point momentary stimulation and multi-points measuring.

全枪模态试验通过单点瞬态激励、多点测量方法，测出机枪上各测点的频响函数，识别出机枪的各阶模态参数。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。