模形式

The superposable die has used the true thing form in the structure, calculated fell the material, the drawing and the counter- drawing effective range size.

复合模在结构上采用了正装的形式，计算出了落料、正拉深和反拉深工作部分的尺寸。

The superposable die has used the true thing form in the structure, calculated fell the material, the drawing and the counter- drawing effective rang

复合模在结构上采用了正装的形式，计算出了落料、正拉深和反拉深工作部分的尺寸。

According to the typical rib-web parts,different kinds of cushion plates are designed for local loading form ing.The local loading method is used to control flow direction and distance of superfluous metal of web plate to avoid the form ing defects,such as overlap and underfilling,and the isotherm al deform ation condition is employed to improve metal filling and decrease die pressure.

针对典型筋板类锻件，设计了不同形式的局部加载垫板进行局部加载，通过局部加载技术控制腹板处多余金属的流动方向和距离，避免产生折迭、充不满等缺陷，并且利用等温变形条件改善金属充填质量和降低模压力。

The result shows that if students are hinted by forms of analogy, their relation schema of such type will be helpfully activated and that will be in the interest of the formation of conjecturing.

结果显示学生如果无法提取某种类型的关系结构，在经由类化或类比形式的提示，可以帮助学生活化该类型的关系基模，而有利於臆测的形成。

The equations of the equivalent relaxation moduli are shown in general form.

推导了均匀化方法计算等效松驰模量的一般形式。

Ccording to the characters of porous metals, a new effective bulk modulus formula with simpler expression was obtained by considering the heat exchange between the metallic skeleton and air in pore on the basis of phenomenological Biot-Allard model, therefore an extended sound absorption model was put forward.

bstract 根据金属骨架多孔材料的特点，在Biot-Allard刚性骨架多孔材料内流吸声模型的基础上，考虑金属的热导特性，推导出一种新的、形式较简单的有效体积模量表达式，从而得到了一种扩展的吸声模型。

In the open die forging ,the type of flash has great influence on the process of forging.

开式模锻中飞边槽的形式对锻件成形过程的影响较大。

In consideration of the difference between two parts,insert blocks on moving half and fixed half were combined;and the compounded core-pulling of slanted pushing rod,dog-leg cam and slide block was applied to finish the demoulding of internal and external side concave.

介绍了1副在同1副模具中注射成型2个差异性较大的塑件的模具结构，该模具设计时综合考虑了2个塑件的差异性，分别采用了动、定模镶块组合的结构形式，并使用斜推杆、弯销与滑块复合抽芯来完成内外侧凹脱模。

Combined lining of the primary bolting and shotcrete lining and the secondary formwork puring concrete lining is applied to the system of waterproofing and drainage at Yanlieshan tunnel of Jiujiang Jingdezhen road.

九江至景德镇高速公路雁列山隧道防排水系统采用初期锚喷砼和二次模注砼的复合衬砌形式。

Based on the Darcys law, the theoretical model of permeability measurement was established. And the influence of different testing methods and major process parameters such as fabric structure, fiber volume fraction, injection pressure, flow rate and resin viscosity on preform permeability were investigated in details. It was found that the permeability of fibrous reinforcement mainly lied on the preform architecture.

文中首先根据达西定律建立了渗透率测量的理论模型，深入研究了不同的测试方法及主要工艺参数(纤维织物织构、纤维体积含量、充模压力、流动速度、树脂粘度)对渗透特性的影响规律，发现多孔介质增强材料的渗透率主要取决于纤维织物的结构形式，预成型体孔隙分布及其体积分数、压实性对渗透率有较大的影响，提高充模压力和流动速度可以缩短充模时间，在一定程度上可以提高渗透率。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。