模套

Using the feature technique,a set of flashless die forging CAPP system for gear blanks is developed.

运用特征技术，开发了一套齿轮坯的闭式模锻 CAPP系统。

A set of technological specifications fit for laser surface quenching have been obtained in view of the punching die of T12 steel lamp holder through heat tr-eatment, metallographies analysis and industrial application etc.

针对T_(12)钢灯头冲孔凹模，经过热处理、金相分析检测、工业应用等试验过程，研究总结出一套适于激光表面淬火的工艺规范，使该模具工作寿命平均提高近3倍。

At the end of this work, two separate computer programs are provided for viewing the recommended fabrication process of water/oil tank of the double-bottom FRP fishing boat, and calculating the material properties of the FRP laminates.

以上成果，藉由两套互动式软体，分别提供船厂作为FRP双层底油水柜施工教材，使得施工经验得以传承；针对FRP积层特性，吾人可对不同积层板计算出其杨氏模数与强度，经与实际测试比较，误差可在10%以内，对於工程师来说十分有帮助。

In this paper, a set of scheme to test the static and dynamic performance of A/D converters was presented.

2本文设计了一套测试模数转换器静态和动态参数的方案。

Production of various major domestic and international pressure feed granulators the roll, eccentric shaft, the drive wheel, Central-and pulley, bushings, flanged, bearings, shaft and various marine accessories, such as forging, and to undertake various forging processing (forging The largest diameter up to 2000 cm, the largest weighs 2,000 kilograms).

主要生产国内外各种饲料制粒机的压辊、偏心轴、传动轮、环模以及滑轮、衬套、法兰、轴承、各种轴和船用锻件等配件，同时承接各种锻件加工（锻件最大直径可达2000cm，最大的重量为2000公斤）。

Mainly engaged in hardware, plastic products, including: knives, kitchenware, beauty kits series, multi-purpose pliers, scissors, barbecue tools, casters, latex gloves, opened bottle can opener, wire plating rack, CD racks, garden tools, cake mold, Mixer and so on.

主要经营五金，塑料制品，具体包括：小刀，厨房用具，美容套系列，多用钳，剪刀，烧烤用具，脚轮，乳胶手套，开瓶开罐器，铁线电镀架，CD架，花园工具，蛋糕模，打蛋器等等。

Note that if a moving half register or locating ring (9) in incorporated in the design, this feature nominally secures the bush in position.

注意，假如设计了动模定位器或定位环（9），如图，这个部件在名义上就提供了对导套的固定和定位。

From the analysis of automobile vibration sources and the human responses to vibration, a mechanic model of man-chair-vehicle system with 13 degrees of freedom is built by vibration pattern analyzing technology. Using the random vibration theory, the calculating methods are developed for parameters, including vibration pattern, transfer function, wheel transient load, and acceleration of seat, automobile ride quality simulation software is developed.

通过分析汽车振动源和人体对振动的反应，用模态综合技术，建立了十三自由度人－椅－车系统的动力学模型，运用随机振动理论，给出了振动形态、传递函数、悬架动挠度、车轮动载荷、座椅加速度等参量的计算方法，开发了一套&汽车平顺性仿真软件&并利用已有的汽车数据，对汽车行驶时的振动特性进行了仿真，得到了重要结论：发动机与轮胎刚度、阻尼，后桥阻尼对驾驶员座椅处的振动影响不大；驾驶员座椅的垂直刚度增加很大时，对垂直方向振动响应比较大；前桥刚度、阻尼对驾驶员座椅处的振动影响较大；前轮胎刚度对前桥振动影响较大，前轮胎刚度增加，则振动加强；后桥刚度对汽车平顺性有一定影响，后桥刚度减小，则座椅处垂直加速度减小。

This research sets the target of zinc die-casting design, the craft parameters parts crafts analysis, the choice of die-casting machines and platoon Yak system design, the introduction of institutions, national aircraft design, shape parts design, structural components design, die-casting mould technical requirements and material composition, a total of nine chapters.

本课题研究的对象是锌套的压铸模设计，包括工艺参数的选择，零件的工艺分析，压铸机的选用及排溢系统的设计，推出机构，模架的设计，成形零件的设计，结构零件的设计，压铸模的技术要求及选材等，本课题的设计论述出了各部分的设计方法与原则以及计算设计过程和必要的强度校核。

Dongguan Exhibition Fenggang metal mold Fitch Dongguang Fenggang town, the company specialized EDM, Drilling Machine, EDM consumption and mold materials, such as precision room supplies, wire-cut filters, ion exchange resins, ion exchange resins , derusting water KC-12.K-200, RHV600, electrical conductors are flush Tsui, insulation board, wire guide pulley, tension wheels, drilling machine with diamond Introduction Tsui, VITOL processing fluid, and fast wire molybdenum wire with a bright, steel guide pulley, precious stones guide pulley, guide pulley components, guide pulley bushing, conductive block.

东莞市凤岗展誉模具五金位于东莞市凤岗镇，公司专业经营线切割机，打孔机，火花机消耗材及模房等精密用品，线切割用过滤器，离子交换树脂，离子交换树脂，除锈水KC-12.K-200，RHV600，导电体，冲水咀，绝缘板，引线导轮，张力轮，打孔机用钻石导咀，VITOL加工液，及快走丝用光明钼丝，钢导轮，宝石导轮，导轮组件，导轮衬套，导电块。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。