模套

In this paper we acquaint the reader first with the algebraic semantics which is corre-sponding to the Kripke's semantic having nested domaius. By an application of the completenesstheorem on relational semantics of the quantified normal modal systems with nested domains proved in Hughes and Cresswell's method to prove a completeness theorem on relational algebraic semantics of those system. Next for normal systems with semantics which admits arbi-trarily variable domains we use Henkin's method to prove a c...

本文首先讨论嵌套论域语义的相应代数语义并由Hughes和Cresswell在［5］中建立的关于具有嵌套论域的正规量词模态系统的关系语义完全性定理推出其相应的代数语义完全性定理：然后对于具有任意可变论域语义的正规系统，我们用Henkin方法给出其关于狭义Kripke语义的关系语义完全性定理，由此通过将关系语义转化为代数语义从而亦推得其代数语义完全性定理。

Based on the single-axis air-bearing test bed, three experiment schemes are creatively designed for investigating the behaviors of rigid-flexible coupling dynamics:(1) experiment scheme for structural dynamics problem under a non-inertial frame,(2) experiment scheme for rigid-flexible coupling dynamics with unknown large overall motions,(3) experiment scheme for modal analysis of a typical rigid-flexible coupling system.

为了能更深入地揭示刚柔耦合动力学特性与验证本文提出的一次近似模型的正确性，最后重点介绍了我们在单轴气浮台动力学仿真实验平台基础上，经过多次探索和总结，创造性地设计的三套刚柔耦合动力学实验方案：(1)非惯性系下结构动力学问题的实验研究方案，(2)大范围运动为自由的刚柔耦合动力学问题的实验研究方案，(3)刚柔耦合系统模态分析实验方案。这三套方案从实验的角度来讲是可行的，这为下一步的实验工作打下了基础。

In addition, in-mold labels and shrinking set of winding the growth rate of the label are more than 5%, with shrinking set of 2006 it is expected that the growth of 14% in North America to become the industry's largest liangdian, coupled with a sticker on the filmogen in the use of, all these are to business card printing and membership card making higher requirements.

另外，模内标签和收缩膜套缠绕标签的增长率都超过5%，其中收缩膜套2006年预计在北美增长14%，成为标签行业最大的亮点，加上不干胶标签中薄膜材料的更多使用，这些都给制卡和会员卡制作设备提出更高的要求。

This article is subject to the diaphragm process and stamping die design, the blanking-punching composite modulus and jumping over two sets of single-mode processes mold design.

本文的课题是膜片弹簧的冲压工艺及模具设计，进行了落料—冲孔复合模及冲槽单工序模两套模具的设计。

This article is subject to the diaphragm process and stamping die design, the blanking-punching composite modulus and jumping over two sets of single-mode processes mold design.

摘要本文的课题是膜片弹簧的冲压工艺及模具设计，进行了落料—冲孔复合模及冲槽单工序模两套模具的设计。

Jig drilling units are set up for the location of holes to be machined precision jig fixture at all types of machine tools accounted for the largest proportion.

钻模上均设置钻套，用以被加工孔的位置精度，钻模在各类机床夹具中占的比重最大。

Both ends of the die cutting knife vrachyaxis are used with hole Loy, wood box fixed to prevent transportation die-cutting knife inter-articular in the box.

模切刀两头的长轴需不分别用带孔的木块套上，木块在箱边固不退，制止输送洋模切刀在箱边移位。

This paper presents the Proteus software under a micro-controller board simulation method, and gives a digital-to-analog converter, analog-to-digital conversion、ISP programming、numeral clock 、real-time digital clock ﹑ Lantern experimental keyboard ﹑lattice LED ﹑ Relay, voice and other tenets of the hardware modules and software flow chart.

本文介绍了在Proteus软件下实现了一套单片机实验板的仿真方法，并给出了数模转换、模数转换﹑ISP编程﹑数字钟﹑实时时钟、键盘﹑彩灯实验﹑点阵LED显示屏﹑继电器、语音等模块的硬件原理及软件流程图。

This paper presents the Proteus software under a micro-controller board simulation method, and gives a digital-to-analog converter, analog-to-digital conversion、ISP programming、numeral clock 、real-time digital clock ﹑ Lantern experimental keyboard ﹑lattice LED ﹑ Relay, voice and other tenets of the hardware modules and software flow chart.

论文编号：JD607 包括开题报告，任务书，外文翻译，论文字数：10522，页数：46本文介绍了在Proteus软件下实现了一套单片机实验板的仿真方法，并给出了数模转换、模数转换﹑ISP编程﹑数字钟﹑实时时钟、键盘﹑彩灯实验﹑点阵LED显示屏﹑继电器、语音等模块的硬件原理及软件流程图。

The float plate block and slide block are controlled by the two-way wedge and located by the ringer.

该模具的凹模由固定部分和活动部分组成，浮动凹模镶块和滑块部分由双向斜楔控制、套环定位，保证了横向和纵向压料的精度，满足了零件质量要求。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了