模塑的

Mj, imported na nga siguro yung 7.50 na cellophane sa bookstore,makapal kasi yung imported.i bought my molder a long time ago sa Divi nga.Pero my sis-in-law discovered a new store NEW SINKIAN HENG CORP. address: C. Palanca near Quinta market.

兆焦耳，进口娜雅siguro容7.50娜玻璃纸SA服务书店makapal卡西容imported.i买我的模塑很早以前SA服务划分nga.pero我矽统在法发现了一种新的存储新sinkian恒股份有限公司地址：长菲近金塔市场。

The purpose of this thesis is to study rotational moulding of molding continuous fibre reinforced thermosetting resin composites.

基于此，本文工作的目标是使用通用型不饱和聚酯树脂为原料研究适用它的旋转模塑成型工艺及长纤维增强技术。

Resin transfer molding mould was manufactured with bisphenol-A epoxide vinylester resin as matrix,poly as low shrinkage additive and glass fiber tricot as reinforcing material,according to the basic requirement of matrix resin of RTM mould.

根据树脂传递模塑模具对基体树脂的基本要求，选用双酚A环氧乙烯基酯树脂为基体，聚乙酸乙烯酯为低收缩添加剂，玻璃纤维经编织物为增强材料，并加入相应的助剂，制备了复合材料RTM模具。

In this latest application, two injection-moulded halvs of the Land Rover headlamp and screenwash water container are hot plate welded together before an operator loads each unit into the assembly an test station.

最新的应用实例是，路虎前照灯两个半块注射模塑块的和挡风玻璃清洗液容器焊接在一起，之后将各个模块安装到测试台上。

The ratio and the magnitude of warpage depend on the compound properties.

封装的翘曲率及翘曲幅度依赖于模塑料的特性。

The results showed that the optimum preparation conditions of moulding materials were as follows: moler ratio of melamine to formaldehyde 1:2.5, water turbidity of the reaction end point 1:3, content of cellulose 42%~48%, fineness of moulding powder 100~120 mesh.

结果表明，三聚氰胺与甲醛物质的量比为1：2.5、终点控制在水浊度1：3，纤维素用量42%~48%，干燥温度70℃，球磨至100~120目时，制得的模塑料性能良好，符合国家日用级产品相关标准。

It could achieve expected surface resistively, without an effect on the gloss and transparency of final products.

推荐用量为，薄膜0.5%，而模塑制品0.7-0.8%；达到期望表面电阻的同时，不会影响到制成品的表面光泽及透明性。

These primordial experiences have still been kept, though man has been gradually secularized.

宗教肯定了人类最初的文化创造，也模塑了人类的生活方式和劳作方式。

Bonded degree not strongly, the label paper is not enough material and softness to the skin, that produces bubbles, the label also be detached to Workbench, werenot, mainly due to the pressure-sensitive labels when casting plastic bottle blowing temperature, pressure, cooling temperature respects to strictly control, if the control is not good occur label and body detachment.

粘合度不强，标签纸材质硬、柔软度不够，容易使产品产生气泡，标签也会撕下来，粘固不牢固，主要是因为在贴标时入模塑料温度，吹瓶时的压力、冷却温度等几方面都要严格控制，如果控制不好会出现标纸和瓶身脱离的现象。

A really nice claymation made by molding a clay figure and filming it.

一个非常好的claymation模塑由一个泥塑和拍摄的。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。