模具

Instrument panel of the automobiles is one of the most difficult mold part, and also it takes long time for milling.

仪表板的汽车是其中最困难的部分模具，也需很长的时间磨。

Because the inside of the plastic part has two round ribs that are difficult to be formed, two inserts are added to make it easier to form mold. The integral surface is camber.

由于塑件中部有两不易成型的圆肋，采用了增加两个小型芯镶件的办法减少加工模具的难度。

This text has introduced the design of the interphone injection mould in detail.

本文详细介绍了interphone注射模具的设计。

t : This text has introduced the design of the interphone injection mould in detail.

本文详细介绍了 interphone 注射模具的设计。

Abstractt :This text has introduced the design of the interphone injection mould in detail.

本文详细介绍了interphone注射模具的设计。

Methods: the animal model was produced by means of putting special moulds on the male rats being bred in cages separately. Using CHAIHUSHUGAN POWDER as trial drug to smooth the circulation of liver-Qi, the targets such as oltaction-licking latency % intromission latency, intromission frequency, ejaculation latency,ejaculation frequency, post-ejaculation interval had been observed. Fluorospectrophotometry had been used to measure the content of 5-HT in respective specimen which had been produced by separating plasm, fluid of broken platelets from rats venous blood and homogenating the hypothalami.

通过带模具单笼饲养法造模，以柴胡疏肝散作为疏肝理气试验用药，观察大鼠的嗅舔潜伏期、插入潜伏期、插入次数、射精潜伏期、射精次数、射精后不应期；取大鼠静脉血和下丘脑，制备血浆、血小板破碎液和下丘脑匀浆，运用荧光分光光度法检测各标本5-HT的含量。

In this thesis, the results of extremal work path theory are adopted, and the FEM based on deformation theory is formulated. The Inverse Finite Element Approach in sheet metal forming is studied in detail, and an Object-Oriented Finite Element Analysis program is developed, which provides rapid and effective means for stamping process planning and die design.

本文运用极值路径理论推导出基于形变理论的有限元公式，研究了钣料成形有限元逆算法，开发了面向对象的有限元分析程序，为冲压工艺和模具设计提供了快速有效的分析手段。

Wind filler is made from silencing material with noise 5 db lower than national industrial standard, whilst suction wind strength 120-150 Pa higher than national industrial standard and up to 350 Pa, leaving strong suction and desirable ironing effect and resolving insufficient suction of old ironing table.

吸风压强比国家行业标准高120-150Pa，最高达350Pa。使吸风强劲，使熨烫效果更好。解决过去老式烫台吸风不足的弊病。风门全程采用机械模具冲制，使风门光洁顺畅及密封性好。

Ge Yusheng, General Secretary with Chinese As sociation of Light Industry Machinery seriously mentioned that Baodao-B-3 low-noise, strong-suction V suction-ironing table is unique in its kind, which successfully overcame the ins ufficient suction of old ironing table with its suction wind strength up to 350 Pa, whose whole stroke of suction valve adopts stamping by machinery mould, leaving smooth suction door of good sealing and low-noise etc. My personal involvement in this quality inspection witnessed the proven quality of Baodao brand.

中国轻工机械协会秘书长，高级工程师葛余生认真地讲宝岛牌YTT-B-3型低噪音强吸风，V型吸风烫台与同行业生产的不一样，很具有特色，解决了过去老式烫台吸风不足的弊病，吸风压强最高达350Pa，吸风阀门全程采用机械模具冲制，使风门光洁畅顺及密封性好，噪音低等特点(我亲自参加了这次质量检测，宝岛品牌名副其实)，宝岛品质国内一流，与国际同步，替代进口，价格从优。

Isothermal spheroidizing process for H13 hot-working die steel was studied in th is paper.

例句1。对H13热作模具钢的等温球化退火工艺进行了试验研究。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。