模具

The Shanghai Roddex Bath Hardware company with 30 years prfessional manufacturing experience,has been devoting continuously to research and development on the sanitary fitting, It has formed the product design,mold design,mold design,mold manufacture, brass gravity casting, brass forging,zinc alloy die casting,machining,polishing and buffing,chrome palting,surface treatment,the assembling and so on the specialized complete set production system,becomes one of the most outstanding faucets manufactures in china.

更多 上海劳达斯洁具有限公司积三十年水龙头专业制造之经验，一直致力于卫生洁具，火龙头的研究与开发，已形成了产品设计，模具设计，模具制造，铜重力铸造，铜挤压，锌合金压铸，机械加工、抛光，电镀、表面处理、装配等专业成套生产体系，集科、工、贸为一体的经济联合体，是目前国内最具规模的专业生产水龙头厂家之一。

The Shanghai Roddex Bath Hardware company with 30 years prfessional manufacturing experience,has been devoting continuously to research and development on the sanitary fitting, It has formed the product design,mold design,mold design,mold manufacture, brass gravity casting, brass forging,zinc alloy die casting,machining,polishing and buffing,chrome palting,surface treatment,the assembling and so on the specialized complete set production system,becomes one of the most outstanding faucets manufactures in china.

上海劳达斯洁具有限公司积三十年水龙头专业制造之经验，一直致力于卫生洁具，火龙头的研究与开发，已形成了产品设计，模具设计，模具制造，铜重力铸造，铜挤压，锌合金压铸，机械加工、抛光，电镀、表面处理、装配等专业成套生产体系，集科、工、贸为一体的经济联合体，是目前国内最具规模的专业生产水龙头厂家之一。

The PCVD plasma impregnation process of hot forging die includes surface deoiling, polishing, supersonic cleaning in acetone and alcohol dewatering of the die after quenching at 1070 deg.c and tempering at 530 deg.c; plasma nitriding in a industrial PCVD vacuum furnace; and PCVD plating.

本发明公开了一种精密叶片热锻模具的PCVD等离子体渗镀复合强化方法，将经1070℃淬火，530℃回火后的叶片模具(HRC＝43-50)经表面除油、抛光后浸入丙酮中超声波清洗，酒精脱水；然后放入工业型PCVD真空炉内进行等离子体渗氮和PCVD镀膜处理。

The die contacting press is the special equipment of automobile die .

模具研配液压机是研配汽车模具的专用设备。

This paper also introduces a new mold base design method, which applies technique of Case-based Reasoning, and presents the structure and manager of Case Base of mold die of press die.

本论文运用基于事例推理技术，对冲裁模设计中的模具结构设计进行了研究，提出了模具结构的CBR设计方法，并以此为基础提出了冲裁模结构事例库的结构和管理方案。

Under static load, and the impact of lower load mode or hot extrusion press forging die.

此钢系高强度热作模具钢，可用於制造工作温度≥550℃并承受较高的静载荷，而冲击载荷较低的锻造压力机模或热挤压模具。

Die spark a full set of manufacturing and other imported equipment, a complete mold design.

火花机等全套模具制造进口设备，有完整的模具设计。

Figure 32 A 3D die set assembly has the whole picture of the die set in 3D.

图 32 在3D中3D模具装配具有模具的全部图形。

At the same time,three dynamic models of cylinder powder green-preform are set up ,which are :die and corefixed on the die shoe , core moving with green-preform, core and die moving downwardin relation to green-preform. The theoretical equations of the green-preform densities andpressing stresses of the three pressing conditions are also derived.

同时建立了凹模与型芯固定在下模座、型芯随压坯一起运动和型芯与凹模相对于压坯向下运动等三种圆环形粉末压坯压制的力学模型，导出了这三种压制条件下的压坯密度与压制压力的理论公式；其结果能够指导粉末冶金模具设计，为发挥模具材料的潜力提供依据。

Based on gaining high productivity and the high percentage of material consumption,We made the choice of using two dies to fulfill the design: one progressive die to execute punching, drawing and blanking.we use the second bending die with a wedge to get the two bends.

本设计以提高生产率及材料利用率为出发点，采用两套模具进行该启瓶器的设计：第一套级进模完成冲孔、拉深和落料；第二套模具为楔块式弯曲模，用来完成两次弯曲成形。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。