模

This study is focused on the optimum parameters study of the stamper making process.

本研究是针对光碟微结构模仁的各项制程中，找出影响光碟模仁微结构与粗糙度的最佳各项参数，实验中分别比较V90与IP3650两种光阻剂在控制光阻涂布厚度、显影浓度、显影时间与离子清洗时间，探讨其改变各项制程参数对微结构成型与粗糙度的影响。

The Stanine model can be used to represent the standard module of students' spatial ability.

二、「空间能力量表」能有效建立常模：本研究常模之建立，系采用标准九的标准分数为模式。

For the four laterals simply supported plate, the transverse deflection of plate is expanded over the modal shapes, the electroelastic model with self-sensing actuators plate is given, and the current is considered as output variable of measurement equation. Generalized modal coordinates being state variables, LQG and H∞control is proceeded using the state space equation.

将板的横向位移按模态展开，对配置压电自感作动器的薄板建立了模型，给出以广义模态坐标为状态变量的状态方程和以传感电流为输出的观测方程，在此基础上，对系统进行了LQG控制和H∞控制。

The results also show that the module of state vector is more sensitive than other parameters stat...

研究结果还表明，相对于态矢量增量的模、态矢量方向的改变等参量，态矢量的模在震前的变化更为敏感，此外，对于相同震级的地震，最佳扫描区域尺度大小不一，并对这些现象进行了一定的解释。

The other, involving Chapter 7, is about the stationary probability distribution of a single-mode laser.

本论文进行了两个方面的研究，一个是关于噪声对双模激光模间竞争的影响，包括第二章至第六章的内容；另一个是用内插法计算单模激光的定态几率分布，为第七章的内容。

The mold is clamped into the machine with the front half remaining stationary (on the barrel side of the machine) and the back half being the movable half.

模具被锁紧在机台上，前模固定不动，后模则可以移动。

The empirical mode decomposition method is introduced to extract the trend item of gyro's drift, but the local mean estimation isn't precision and the end effects exist in the conventional EMD method. The two-tap adaptive time-varying filter and the adaptive border estimation are used to modify the EMD. After the trend extraction, the method of time series analysis is used to make the autoregressive moving average model for stationary time series.

根据陀螺漂移的特性，提出采用经验模分解的方法对其趋势项进行提取，但传统的经验模分解方法存在局部均值估值不准，插值过程存在端点效应的问题，因此，本文又引入二拍自适应滤波及自适应边界估值来对原方法加以改进；在成功提取趋势项后，通过采用时间序列的分析方法，建立了陀螺漂移平稳时间序列的自回归滑动平均模型；并得出陀螺漂移模型可近似为常值加一阶马尔可夫过程这样一个结论。

The results show that the entanglement of field-atom reduced to a stationary value with time evolution and the entanglement between two modes increase to another stationary value with intrinsic decoherence, and the values only depend on the two-mode photon number and mean photon number.

结果表明，存在内禀退相干时，随着时间的演化，场一原子纠缠逐渐减小到一个确定值，而模间纠缠逐渐增大到一个确定值，两者演化的最终值只取决于双模光子数差和平均光子数，而与内禀退相干因子无关。

With 3.0 t empty dual-use steam forging hammer, 1.0 t empty dual-use steam forging hammer, 750 kg, 400kg, 250kg, 150kg Kong Qichui a total of seven, made 3.0 t, 2.5t of a hammer plywood Taiwan, the construction of 2 m × 1.5m × 1.0m two large coal-fired furnace, a gas generator furnace, resistance furnace, Oil Furnace, Meilu stoves and other heat treatment of the four sets, with the following specs for Φ550 Saw 5,φ100 major fault Liu and other supporting material under the equipment, and has CW611250, T68, and other machining equipment, more than 60 species of vehicles, milling, planing, grinding, boring jobs complete, the main products φ820 × 60 × 1300 following the suppression of three products,φ273 high-pressure forging Billet-three links, all kinds of high-pressure-welded flange and 3.0 t following forging free, annual production capacity of 2400 t.

拥有3.0t空蒸两用模锻锤，1.0t空蒸两用模锻锤，750kg、400kg、250kg、150kg空气锤共7台，自制3.0t、2.5t夹板锤各1台，建造2m×1.5m×1.0m大型燃煤加热炉两座，煤气发生器加热炉1座，电阻炉、油炉、煤炉等热处理炉具各4套，拥有加工规格为Φ550以下锯床5台，φ100大型断料机等配套下料设备，且拥有CW611250、 T68等机加工设备60余种，车、铣、刨、磨、镗工种齐全，主要产品φ820×60×1300以下压制三通成品管，φ273高压锻制三通方坯，各种中高压平对焊法兰及3.0t以下自由锻件，年生产能力2400t。

The question is how much of the problem of stent failure may be the result of stents not being put in right.

问题是印模失败的问题在多大程度上会使印模膏不被放在正确的地方。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失