模

According to the results of triaxial compression test, the relationship of cement soil mixed with or without glass fiber concerning stress and strain in different ages and confining pressures was analyzed. Meanwhile, some parameters of cement soil mixed with glass fiber, such as shearing strength parameter, modulus of deformation and relationship between compression strength and deformation modulus were obtained.

根据玻璃纤维-水泥土的三轴压缩试验结果，分析了其在不同围压与龄期下的应力-应变关系，并得到玻璃纤维-水泥土的剪切强度参数、变形模量E50及变形模量与抗压强度qu的关系。

Dynamic rheological test was introduced and the dynamic shearing modulus G', the loss modulus Gand the complex viscosity of coatings were measured.

把流变动态测试引入铸型涂料的研究，测量出了铸型涂料的动态剪切模量G〓、损耗模量G〓和复合粘度η〓。

The results show that the amorphous PLGA fiber with porous structure (0.1-1.0 μm) is obtained by diluted solvent spinning method and the mechanical properties is affected by pressure and temperature. Bending strength and shearing strength of the samples increase firstly and then decrease with the increase of molding temperature and pressure. While the molding temperature is 160℃and the pressure is 105MPa, the PLGA materials possess optimal mechanical properties, bending strength, shearing strength and bending modulus 187.3 MPa, 100.0 MPa and 2.5 GPa, respectively. The mild temperature molding PLGA materials are desired to play a grate role in non-bearing internal fixation devices.

研究结果表明：非晶多孔结构的PLGA纤维可通过溶液沉析纺丝的方法获得，其孔径为0.1~1.0μm；压制压力和压制温度对材料的力学性能影响较大，材料的抗弯强度、剪切强度和抗弯模量均随着温度和压力的增大而先增大后降低；在压制压力为105MPa，压制温度为160℃时，试样的力学性能比较理想，此时，其抗弯强度可达到187.3MPa，剪切强度达到100.1MPa，抗弯模量达到2.5GPa，可望作为非承重部位骨折愈合内固定材料。

Finally the terramechanics parameters of the lunar soil were calculated as:the deformation modulus K=1635 kN/mn+2,the sinkage exponent n=1.22 and the shearing strength displacement modulus k=1.35 cm.

最后，计算出了月壤的变形模量K为1635 kN/mn+2、变形指数n为1.22，剪切变形模量k为1.35 cm。

Finally the terra-mechanics parameters of the lunar soil were calculated as: the deformation modulus K=1635kN/m(superscript n+2), the sinkage exponent n=1.22 and the shearing strength displacement modulus κ=1.35cm.

最后，计算出了月壤的变形模量K为1635kN/m(上标 n+2)、变形指数n为1.22，剪切变形模量k为1.35cm。

With the increased design complexities brought in by applying different RETs, post-RET sign-off verification is quickly becoming necessary.

分辨率增强技术的应用使得光刻用掩模图形日趋复杂，而掩模制造成本和制备时间也随之增加。

The fuzzy control method was adopted to design a fuzzy switching function to replace the sliding mode signum function, and the chattering phenomenon was restrained greatly.

针对滑模切换函数的高频"抖动"现象，采用模糊控制方法，设计了模糊切换函数，削弱了滑模切换函数的"抖动"。

This paper studied the effects of different modulus of sodium silicate in old newspaper deinking.

本实验制备了不同模数的硅酸钠，研究了硅酸钠模数对旧报纸脱墨的影响。

In this thesis, the methods for solving eigenvalue problems and conventional reanalysis methods are studied firstly. Then, a new reanalysis method for real modal reanalysis of structures subjected to topological modification with added degrees of freedom is presented. This method is composed of the single step perturbation method and the Rayleigh-quotient iteration. The numerical examples show that this reanalysis method is very effective and high-quality.

本文首先在对常规的特征值数值求解方法和重分析方法研究的基础上，针对实模态的自由度增加的结构拓扑修改重分析，提出了一种新方法，该方法由于结合了单步摄动法和瑞利商逆迭代法两者的优点，应当是一种比较理想的重分析方法，算例的数值结果也有力的验证了该方法确实是一种高精度、十分有效的实模态重分析方法。

According to a survey of HDD development and its current situation at home, a new kind of equipment for hydrodynamic deep drawing has been developed, which was constructed on the basis of a conventional single-action press with general hydrodynamic deep drawing die sets.

在对充液拉深技术的发展和国内具体情况调查的基础上，研制了基于通用单动液压机的通用充液拉深模架型式的充液拉深装备，整个装备由模架、液压控制系统和计算机自动控制系统等三部分组成，实现了充液拉深成形过程的液室压力和压边力的实时控制。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失