模
- 与 模 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The expression of differential pair CM inductance on PCB is deduced under the condition of departuring ground plane center and spanning discontinuously ground plane based on the model of microstrip.
以多层板的微带线为模型,推导出在偏离地平面中心以及跨越不连续地平面的情况下,PCB上差分对共模电感的定量表达式,并对其共模噪声的特性进行了详细讨论。
-
Results The scores of SCL-90 factors were lower than that of the norm of college students while some factor scores were higher than the national norm of youth. The top three positive factors were obsessive-compulsive (25.2%), depression (18.9%), interpersonal sensitivity (18.4%). The results of Logistic regression analysis showed that bad relations with roommates, bad relation with spouse or lover, failure in completing the study plans, emotional volatility, suffering from disesteem or discrimination and lack of career planning were risk factors.
结果 该群体SCL-90各因子分值均低于大学生常模,部分因子分值高于全国青年常模;因子呈阳性比例较大的依次为强迫25.2%,抑郁18.9%,人际关系敏感18.4%;多因素Logistic回归分析显示,与寝室同学关系不好OR=1.561,95% CI=1.190~2.047;与恋人或配偶关系不好OR=1.342,95% CI=1.044~1.725;读书计划完不成OR=1.282,95% CI=1.066~1.542;情绪波动大OR=1.614,95% CI=1.303~1.999;受到歧视或冷遇OR=1.430,95% CI=1.151~1.778;不知道职业生涯规划OR=1.606,95% CI=1.354~1.917,提示些因素是影响硕士研究生心理健康的危险因素。
-
Results The scores of SCL90 factors were lower than that of the norm of college students while some factor scores were higher than the national norm of youth.The top three positive factors were obsessivecompulsive(25.2%),depression(18.9%),interpersonal sensitivity(18.4%).The results of Logistic regression analysis showed that bad relations with roommates,bad relation with spouse or lover,failure in completing the study plans,emotional volatility,suffering from disesteem or discrimination and lack of career planning were risk factors.
结果 该群体SCL-90各因子分值均低于大学生常模,部分因子分值高于全国青年常模;因子呈阳性比例较大的依次为强迫25.2%,抑郁18.9%,人际关系敏感18.4%;多因素Logistic回归分析显示,与寝室同学关系不好OR=1.561,95%CI=1.190~2.047;与恋人或配偶关系不好OR=1.342,95%CI=1.044~1.725;读书计划完不成OR=1.282,95%CI=1.066~1.542;情绪波动大OR=1.614,95%CI=1.303~1.999;受到歧视或冷遇OR=1.430,95%CI=1.151~1.778;不知道职业生涯规划OR=1.606,95%CI=1.354~1.917,提示些因素是影响硕士研究生心理健康的危险因素。
-
The system contains a friendly user interface in which designer can set and choose design parameters, and understand the design dissimilitude during operation process.
配合此建议值,并达到符合消费者足部曲线之合适性,系统自动进行内衬模组与鞋垫模组选择,使消费者可得到最合适自己脚型的鞋款。
-
Let R be a ring with identity. Then R is a division ring if and only if every unitary module over R is a free module.
R 是有单位元的环,它是除环的充分必要条件是其上的所有幺模都是自由模。
-
Independently developed by the Division I-coated diamond ring-Series ring than ordinary high-yield 40 percent.
由我司独立开发的涂覆金刚石环模系列比普通的环模产量高40%。
-
It introduces causes of formation of polarization mode dispersion、describing methods in internet and some important concepts about PMD,for example double refraction, coupling, primary polarization state and so on.
介绍了偏振模色散的成因、国际上常用的描述方法以及有关偏振模色散的一些重要概念,如:双折射,耦合,主偏振态等。
-
This is due to zaimo meet the press, die mrtomated, indentation on the Telegraph on paper produced uponsize, paper that is not being completely cut wearing is produced by uponsize draggle arisento rough edges.
这是由于在模切合压时,模切版上的胶条、压痕钢线对纸张产生了拉力,纸张在未被完全切穿时被产生的拉力拉断出现了毛边。
-
Renqiu existence machining Manufacturing Co., the main production Nail Die, drawing module, Nail knife, cut materials and various special-shaped knife alloy die, as long as there are samples, drawings or my company can in the shortest possible time to produce Customer satisfaction with the mold.
任丘永固机械加工制造有限公司,主要生产制钉模,拉丝模,制钉刀,切料刀及各种异型合金模具,客户只要有样品或图纸我公司便可在最短的时间内生产出客户满意的模具。
-
These components are usually made of iron- or copper-base alloys and very small, so powder metallurgy offers a better method than the processes involving machining, drop forging, die casting, pressing etc.
这些部件一般是铁基或铜基合金,而且尺寸很小,因而用粉末冶金法制造比用切削加工,模锻,模铸,冲压等方法更好。
- 推荐网络例句
-
I didn't watch TV last night, because it .
昨晚我没有看电视,因为电视机坏了。
-
Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.
今年以来,在北京的很多小区里,电梯液晶电视被撤了下来。
-
I'm running my simile to an extreme.
我比喻得过头了。