模
- 与 模 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Using the climatologically mean temperature and salinity from the Levitus data, the solutions with different modes of the gravity waves and planetary waves are analyzed.
利用Levitus气候平均温盐资料,分析了线性理论意义下南海的重力波及行星波的不同模态解,其一阶模的相速度分布与真实地形关系十分密切;通过行星波的临界频率的计算,从理论上描述了南海行星波动的特征。
-
In chapter 4, we retroduce monoial category and center over it. moreover, we introduce weak center over weak hopf π coalgebra. After studying of the relationship between it and Yetter-Drinfeld moduels, we could found they are isomophic.
第五章主要讨论了弱Hopf群余代数上的弱相对Hop(来源:Ab9BC论文网www.abclunwen.com)f群余模,引入了迹运算,中心等,在此基础上对弱相对Hopf群余模的研究。
-
Die-cutting die,coiler,cutting machine etc.
模切模、收卷机、裁切机等。
-
Maximum model values are found for the channel matrix Hi of each user and for each column vector of the matrix, position information of the matrix is transmitted to a transmitting terminal, the transmitting terminal reconstructs the amplitude of each element of the column vector after receiving the position information, and phase position is quantized, wherein, after reconstruction, the amplitude of the element with the maximum model value is larger than that of other elements of the column vector, and a quantized angle of the element with the maximum model value is smaller than that of the other elements of the column vector; c.
对每个用户的信道矩阵Hi,对该矩阵的每个列向量,找出其最大模值,将其位置信息发送给发射端,发射端收到后对该列向量各元素的幅度进行重构,相位进行量化,其中最大模值的元素重构后其幅度大于该列向量其余元素的幅度,其量化角度小于该列向量其余元素的量化角度;c。
-
The design method of using combined pre_stressing matrix in the drawing die for forming the part with various thickness dimensions was introduced.
介绍了在工件料厚变化较大的拉伸模中采用预应力组合凹模的设计方法,在实际生产中应用取得了良好的效
-
Also in this paper, the magnitude of the common-mode voltage of the system is analyzed and the method of choosing reasonable zero-vectors to restrain the common-mode voltage is presented.
详细分析了基于该控制策略的电机共模电压大小,提出了合理选用零矢量以降低电机共模电压幅值的方法。
-
In this paper, an improved inverter side passive filter was proposed on the bases of analysis of common-mode and differential-mode voltage, and a detailed design procedure of parameters was given.
本文通过对PWM逆变器驱动电机系统产生的共模以及差模电压分析,提出了一种改进型的逆变器端无源滤波器,并给出了参数的设计方法。
-
A novel inverter output passive filter, which can not only reduce differential-mode dv/dt but also suppress common-mode voltage, is proposed.
提出了一种新颖的可以同时降低差模dv/dt和共模电压的逆变器输出无源滤波器。
-
Based on the method of numerical simulation, the diameter of steel billet, entrance half angle of concave die and the dimension of spline were analyzed for the forming force on the spline processing with the help of a rigid-plasticity finite element software Deform 3D.
借助刚塑性有限元软件Deform-3D,采用数值模拟的方法分析了矩形花键轴冷挤压过程中,坯料直径、凹模入模半角及键齿尺寸对花键成形力的影响。
-
When the cavity length is 140 cm and the radius of curvature of the full-reflective concave mirror is 300 cm, the Nd:YAG laser is operated in the stable mode-locking and a pulse train with 27 mJ energy and 35 ps pulse duration is obtained.
当腔长为140 cm,全反射凹面镜曲率半径为300 cm时,激光器运转在稳定的被动锁模状态,输出的锁模脉冲序列能量为27 mJ、脉宽为35 ps。
- 推荐网络例句
-
I didn't watch TV last night, because it .
昨晚我没有看电视,因为电视机坏了。
-
Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.
今年以来,在北京的很多小区里,电梯液晶电视被撤了下来。
-
I'm running my simile to an extreme.
我比喻得过头了。