模
- 与 模 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
This machine is used to punch bridge hole at die cutting ruler and creasing rounded edge at tie point of die cutting plate.
简单介绍:本机用于模切版制作时,模切版连点处模切刀,压痕线冲过桥孔。
-
"Transfer mode" used motor oil transfer mode, there is no overload protection function, the load increased, the four tension rod threads, thread nut transfer mold damage.
&调模&使用油马达调模,没有过载保护功能,负载加大后,四根拉紧杆螺纹、调模螺母螺纹会损坏。
-
The Laguerre-Gaussian modes and linear polarization modes were applied for determining mode intensity distribution. The temperature effect on the mode spot size was evaluated.
我们推导Laguerre-Gaussian 模及线性偏振模的光场强度於空间位置上的分布,并分析温度对横模光点尺寸的影响。
-
In this paper the forming process in the multi-ram forging process of high-pressure tee joint used in power industry and petroleum chemistry industry is introduced.
介绍了采用多向模锻锻制动力工业和石化工业用高压三通的工艺过程,通过FEM模拟总结出高压三通的基本成形规律,并揭示了高压三通多向模锻过程中水平冲头向上翘曲现象及其产生原因,为类似锻件的多向模锻工艺的设计提供了有益的借鉴。
-
In this paper, author also studied strain model theory, and proved that strain model is more sensitive than displacement model to damage.
本文研究了应变模态的理论,并从理论上证明了应变模态较位移模态对结构的损伤更加敏感。
-
Using this method, the effect of the PM-PCF structure on the optical characteristic parameters, including modal field diameters,effective refractive index of space-filling mode, normalized frequency, mode field and single-polarization single-mode region etc., are studied systemly.
在第三章,通过全矢量有限元分析方法详细地分析了保偏光子晶体光纤结构参数对光子晶体光纤的光学特性影响,包括对单偏振单模光子晶体光纤的模场直径、基空间填充模的有效折射率、归一化频率、模场分布、单偏振单模区域等一系列光学特性参数进行了分析。
-
Pull the slip board, up distance switch to loosen , the film motor starts turn to move after receive the signal, turning to schedule length, pass the sense switch control film electrical engineering automatically stop, put the cup into the bottom slip mold , then push to go into, next circulation beginning.
拉出下模滑板,上行程开关松开,胶模电机接到信号后开始转动,转过预定长度,通过电眼控制胶膜电机自动停止,将胶杯放入下模滑板,再推入,下一个循环开始。
-
The transmission mechanism is a plane six-bar mechanism that is made up of two plane four-bar mechanism. Its natural frequencies and mode shapes are obtained by overlapping and synthesizing the mode of each component.
主传动机构是由2个平面四杆机构串联而成的平面六杆机构,通过对各构件的模态进行模态叠加和模态综合,得到传动机构的固有频率和振型。
-
The opposite hydraulic pressure tension is a sheet forming method,using the reverse hydraulic pressure established during the raised mold and sheet enters the concave mold.
对向液压拉深是在凹模兼液压室的型腔内充满液体,利用凸模带动板料进入凹模后建立的反向液压而使板料成形的方法。
-
Blanking, shearing and cutting tools perform their work by some form of "shearing" of cutting action. They include cut-off and shearing dies, blanking dies, piercing, shaving, notching, edging, and trimming tools. The last are applied to the forming of contour by a series of strokes.
落料、冲裁、切断工具都是以某种切断的&剪切&方式进行工作,有切断和冲裁模、落料模及冲孔、精冲、切口、切边、整修等工具,而整修模是通过一系列的冲裁来形成工件的轮廓。
- 推荐网络例句
-
I didn't watch TV last night, because it .
昨晚我没有看电视,因为电视机坏了。
-
Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.
今年以来,在北京的很多小区里,电梯液晶电视被撤了下来。
-
I'm running my simile to an extreme.
我比喻得过头了。