模

During ones term, has completed Japan avionics jig mold, Sanyo Button mold (2 wraps), ohm dragon the key mold altogether four sets of molds decide the material, the design, with the mold, to suppose change, repair the mold work, the JAE jig the quantity produces before leaving job.

在职期间，完成了日本航空电子的夹具模、三洋的Button模具（2套）、欧姆龙的key模具共四套模具的定料、设计、跟模、设变、修模工作，其中JAE的夹具于离职前量产。

In this paper, the state equation of simply supported rectangular panel is established by using the control strategy that is canceling the first k radiation modes.

本文利用声辐射模态的特性，通过抵消前k阶声辐射模态伴随系数的控制策略，以四面简支板为研究对象，在声辐射模态领域首次建立了该物体的状态空间数学模型。

On the basis of normal model transfer, secondary model transfer makes the second model transfer, therefore the line equation is easier.

二次模方法是在常规相模变换的基础上进行第二次模变换，使线路方程更加简化。

The effects of blade stiffness mistuning on the natural frequencies and mode shapes in the frequency veering region were studied based on the lumped parameter model of a bladed disk. A parameter L was introduced to define the severity of mode localization.

基于叶盘集中参数模型，分析了叶片刚度失谐对频率转向区内的系统固有频率及叶片模态振型的影响，提出了一个描述模态局部化程度的参数，仿真研究了频率转向特征对失谐叶盘模态局部化程度的作用规律。

Then we introduce theory of ion-exchange process and how to design multimode Y branch optical splitters. Lastly we do some experiment of how to fabricate the device with Li~+-Na~+ ion-exchange technology.

本文首先比较了多模功分器的种类和制作方法，介绍了离子交换的原理，然后对多模Y分支结构的多模光功分器进行设计，并对器件制作所用的Li~+-Na~+离子交换工艺进行实验研究。

As the growing up of optic-storage media forced the increasing demand of the optic-disc, the importance of the stampers in the optic-disc manufacturing process is getting more significant. The key point of the optic-disc yield and quality will surely depend on the process quality and micro-structure of the stamper.

摘要 随著光电储存媒体的兴起，带动著光碟需求量大增，然而光碟模仁在光碟片制程中占有很重要的地位，光碟片是经由：刻版、显影、电铸，产生微结构模仁，再经射出机射出成型碟片，因此模仁的制程品质与微结构成型条件将是光碟片良率的最大关键。

Photoresist becomes viscous when heated above its glass transition temperature, so the line of photoresist mask can be smoothened.

为了消除重力的影响，在倒置状态下对光刻胶掩模进行高于其玻璃转变温度以上的烘烤，尽量保证光刻胶线条高度的同时得到了光滑的光刻胶掩模，再结合光刻胶灰化技术，进一步得到小占宽比、平直而且干净的光刻胶掩模。

Most common wood use thick die 0.71mm, high 23.2mm of indentation line, many cigarette packaging business card printing and membership card making enterprise regardless of what the backing sheet hard Pack, use the base mould of 1.1mm×0.35mm, I think this is not scientific because different thickness of the backing sheet, you need to make a different width and depth of the base mould.

别致木模切版不小众搁置不薄0.71mm、矮23.2mm的压痕线，好众烟包制卡和会员卡制作企业不管不入不销什么不顶纸的不软包，差别搁置1.1mm×0.35mm的不顶模，不梢人觉得这栽怠工法并不不迷信，因为不差别不顶纸的不薄度不差别，需给制作不差别宽度和广度的不顶模。

Main products includes: XZ42 series moulding machine, Z94 series full automotive core-shooting machine, Z95 series full automotive shell core making machine, ZHTO series core-shooting machine, ZJQ series tilt able pouring machine, core-shooting machine special for producing braking disc, as well as moulding plate pattern, care-shooting box, shell mould/core pattern/box, and so on.

主要产品有：XZ42系列水平分型脱箱射压造型线、Z94系列全自动射芯机、Z95系列全自动壳芯机、ZH70系列射芯机、ZJQ系列可倾式浇注机、刹车盘专用射芯机及型板模、射芯模、金属型和壳模等。

The method of defining pedestal pile foundation deformation modulus is especially discussed in this article, and it takes the Mindlin solution as the starting point using mathematics method to get the Poissons ratio which is the factor influencing foundation soil deformation modulus , and a deformation modulus calculating equation is finally determined.

其中特别论述了扩底桩地基变形模量的确定方法，并从Mindlin解出发利用数学方法得出了影响地基土变形模量大小的因素—泊松比μ，初步确定了比较完善的变形模量计算公式。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。