根轴

It comprises an in-put shaft hinged to its yoke through one axis, and an out-put shaft also hinged to its yoke through another axis, and these two yokes (13) were combined together by only one axis position, perpendicular to that two yoke axes like a cross, so that this combined axis will bend just like the angle bisector of that two shafts to maintain its constant velocity by a few methods, firstly, by using a section of gear teeth mesh at both ends of the shafts' teeth were so polished so that it can turn longitudinally as usual gear, and also sideways, to provide a larger solid angle of turning from ordinary 45 degrees into 60 or even more.

它包括输入轴，其通过一根轴铰链连接于叉形支架，和输出轴，其通过另一根轴也铰链连接于其叉形支架。并且这两个叉形支架(13)只需用一根相对垂直铰链轴相连而组合在一起，使得这种组合的轴总能形成这两个轴的角平分线，以通过少数几种方法保持其恒速，首先，通过用啮合在轴的两端的一段齿轮齿抛光为以能够像普通齿轮一样纵向转动，并且还能够侧向转动，以提供较大的转向立体角，从通常的45度变成60度或更大。

If the first axis is perpendicular to the ground we speak of an azimuthal mounting.

如果第一根轴与地面垂直，就称为地平式支架。

Based on a bounding surface model of the concrete and elastic-plasticity constitutive relationship of steel, this paper establishes the finite element model of the self-stressing concrete filled steel tube short column under axial load and eccentric load. the mechanical performances are analyzed.

对本课题组共进行的37根轴压短柱的试验结果分析，采用分解分析的方法，回归出钢管自应力免振混凝土轴压结构核心混凝土的等效单轴本构关系，与传统的弹性、塑性、断裂、损伤等力学模型相比具有简单实用的特点，便于进行工程计算。

A crystal form consisting of three or more similar faces parallel to a single axis.

斜方晶有三个或三个以上类似的面，且各面均平行于一根轴的一种晶体形式

Similarly, the cotton root-length density reduced gradually from the root axis to both sides of it, and the maximal length density of root was observed at the position of root axis in soil and was diminished by increased dripper discharge.

水平方向上，棉花根长密度由根轴向两边逐渐减小，而且根轴处的根长占总根长比率随滴头流量的增大而变小。

Because on the turnplate axis power is by the turnplate under after the bevel gear commutation, decelerates transmits, moreover their velocity ratio is 6, also because the bevel gear velocity ratio is not bigger than 3 generally, therefore has designed two axes, by realizes the bevel gear two commutation, decelerates.

因为转台上的轴动力是由转台下经锥齿轮换向、减速传来的，而且它们的传动比为6，又因为锥齿轮的传动比一般不大于3，所以多设计了两根轴，以实现锥齿轮的两次换向、减速。

It may be turned by a pulley with a belt or a chain connecting it to a pulley on a second shaft. The supporting structure may be assembled with bolts or rivets or by welding.

一根轴可由联结另一根轴的传动轮的皮带轮或链条轮来带动旋转；支撑结构的组装可用螺拴、铆钉或焊接。

In these devices, one of the shafts is typically driven by a motor or pulley, and the other shaft is driving another device.

在这些装置中，典型的情况是，一根轴由发动机或皮带轮转动，另一根轴将动力传递给其他部件。

The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.

这样，普通织机应具备两根轴，主轴驱动筘座并通过齿轮驱动另一根轴。

Thus a normal loom has two shafts. The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.

这样，普通织机应具备两根轴，主轴驱动筘座，并通过齿轮驱动另一根轴。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。