校准

The introduction of some products are as follows: First, Taiwan's electronic devices Aosta Product:(self-produced self-marketing) program-controlled voltage insulation tester, grounding resistance, leakage current, micro-resistance tester, electrical parameters of the test Transformer parameters meter, insulation resistance tester, electronic load, on-machine, cable tester, variable frequency power supply, LCR Bridge, frequency meter, mV table, the standard signal generator, oscilloscope, signal generator, signal generator, digital multimeter, distortion device, before shaking device, spectrum analyzer, capacitance meter, inductance meter, modulation device, Sweep Signal Generator, Telephone Analyzer, Calibrator Table III, EMC Electric Tester, regulated power supply and so on.

现将部分产品介绍如下：程控耐压绝缘测试仪、接地电阻、泄漏电流、微电阻测试仪、电参数测试变压器参数测量仪、绝缘电阻测试仪、电子负载、导通机、排线测试仪、变频电源、LCR电桥、频率计、毫伏表、标准信号源、示波器、信号发生器、信号源、数字万用表、失真仪、抖摆仪、频谱分析仪、电容测量仪、电感测量仪、调制度仪、扫频信号发生器、电话分析仪、三用表校准仪、EMC电测仪、稳压电源等。

These SRMs are used for calibrating stylus instruments that measure surface roughness.

这些标准物质主要用于测量表面光洁度的探针式仪器的校准。

The front and rear suspension layout also allows the various joints, including the steering arm joints, to yield in a calibrated manner without this affecting driving precision.

前后悬挂布局也允许各种关节，包括转向臂关节，在经过校准的方式产生影响驾驶没有这个精度。

An Optical Microscopy and Image Analysis method was used to certify our Monodisperse Standards against a NIST calibrated stage micrometer.

光学显微镜和图像分析方法过去常常根据 NIST 微米校准方法来证明我们的单分散标准颗粒。

This paper gives several methods to validate these new methods by analyzing images of stage micrometer, metallurgical sample, and images that consisting of definite area in geometric graph, Several kinds of validation methods including of traceability of a quantity value, printing microstucture graph, comparing microstucture photo with standard photos, length meansurement, and area meansurement are discussed in this paper.

通过分析显微镜刻度尺图像、金相样品图像，及给定特定图形且已知面积的图像，依据ISO/IEC 17025检测和校准实验室能力的通用要求，并结合金相检验标准，阐述了金相显微镜利用新方法的方法确认，其中包括量值溯源、金相组织输出、图谱比较、长度类测量和面积类测量的确认方法。

Use the depth guage calibrate the spindle collar step depth and sleeve's height, and make a record for convenient get later processing the spindle front cover preload value.

使用深度表校准主轴深度和步骤衣领的套筒高度，并提出一个新的记录后处理方便获得封面主轴预价值。

Rugged piston-actuated snap action switch automatically resets after the pressure correction. The 2300 delivers dependable, repetitive service even under severe conditions of surge, vibration and shock.

坚固的活塞驱动开关在压力校准后自动复位。2300系列提供了可靠的，可重复操作的设备，即时在严重的振荡、振动和冲击条件。

4The signal is independent of lamp intensity, thus eliminating the need for frequent calibration.

该信号不会随指示灯的亮度而变化，因而不需要经常校准。

The Contractor shall be responsible for the true and proper setting-out of the Works in relation to original points, lines and levels of reference given by the Engineer in writing and for the correctness, subject as above mentioned, of the position, levels, dimensions and alignment of all parts of the Works and for the provision of all necessary instruments, appliances and labor in connection therewith.

承包人负责按工程师提交的书面参考原图的有关点、线和面的规定，忠实恰当地进行测定放线，如上所述，使工程的位置、水平、面积正确无误，并校准工程的各部分，且负责提供与工程相关的所有必要工具、设备和劳力。

The Contractor shall be responsible for the true and proper setting-out of the Works in relation to original points, lines and levels of reference given by the Engineer in writing and for the correctness, subject as above mentioned, of the position, levels, dimensions and alignment of all parts ofthe Works and for the provision of all necessary instruments, appliances and labor in connection therewith.

承包人负责按工程师提交的书面参考原图的有关点、线和面的规定，忠实恰当地进行测定放线，如上所述，使工程的位置、水平、面积正确无误，并校准工程的各部分，且负责提供与工程相关的所有必要工具、设备和劳力。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。