标准时间

The experiment result indicates that the curve of time-temperature has good follow character and temperature difference less than 1 ℃. So it can accurately measure temperature of cable.

通过对标准的热电偶温度传感器与光纤光栅温度传感器的对比实验，表明该系统测量时间－温度变化曲线跟随性好，温度差均小于1℃，符合电力电缆温度状态在线监测的使用要求。

Your clients in testing our TKEKK product, to its current pass 50A, the time fuse was only 40-50 minutes, which did not meet IEC2 / 5 standards, and we have carried out the corresponding analysis, as follows

你们的客户在测试我司所供TKEKK产品时，给其通50A电流，熔断时间仅仅为40-50分钟，不符IEC2/5标准的要求，对此我们进行了相应的分析，如下

A sampling inspection has randomly carried out in warehouse in April 2008, our TKEKK products, to its current pass 50A with fuse time of 70-75 minutes, which has met the requirement (60-80 minutes) as requested.

经抽测仓库2008年4月份生产之TKEKK产品，给其通50A电流时熔断时间为70-75分钟，满足标准（60-80分钟）要求。

When I'm satisfied with the general volume a shell modifier helps me to give thickness to the piece. In this phase, I don't usually bother that much about every single rivet, hole or cut, I just try to develop a good quad topology of the main volumes. Of course the topology is done by taking count of the main cuts and holes, but the rest can be done easily with a normal or bump map. It's up to you to decide how much a single detail is worth to be modeled or can it be put into a bump map. I usually adopt a "comfortable" criteria...it means that if something looks tricky to me to be carved or extruded into an existing geometry I usually put it into a normal map. When you make something for production, you don't usually have much time to model everything, so you need to set priorities.

当我对整个盔甲的体积感满意之后，一个shell修改器就可以帮我给整个盔甲添加厚度，在这个阶段，我通常不会考虑太多那些细小的铆钉，洞眼或者切边，我只是给整个的模型确立一个好的四边形拓扑结构，当然拓扑是通过重视主要的切割和打洞来形成的，但其余那些细小的部分可以用一个normal 或者bump贴图很容易地模拟出来，这由你来决定到底一个细节是值得建模还是放到一个bump贴图里面，我通常采用一个&舒服&的标准，也就是说，如果有什么东西对我来说，在已有模型上再挤出或者开洞是非常麻烦的，那么我就通过Normal贴图来表现，而当你为商业生产制作模型时，你通常都没有足够的时间来把任何东西都建出来，因此你需要设置重点。

During the fire-resistant test, the glass can keep integrity for 90 minutes under 800℃, which reach the national criterion.

在耐火实验中，在800℃温度下玻璃耐火时间达到90分钟，达到国家防火玻璃标准

All tests were successfully conducted for six hours of fire endurance measured against the standard time/temperature curve.

根据标准的时间--温度曲线，所有测试都成功的通过了六小时防火耐久性试验。

Results: We found that (1) the rate of CSF tap test responders was not significantly different between the patients with INPH and SNPH.(2) the rate of CSF tap test responders was not related to the presence or severity of vascular comorbidities in the patients with INPH.

其中快速行走测试时间缩短大於10%以上或认知能力筛选工具总分进步大於1标准差(1SD)以上者或者定义为脑脊髓液穿刺测验反应者。

Standard Practice for Creasing or Bending a Membrane Switch , Membrane Switch Flex Tail Assembly or Membrane Switch Component

发布时间：2002薄膜开关，薄膜开关引线组件或薄膜开关元件折皱或弯曲的标准实施规范

The inventions that meet these criteria, in chronological order, are the compass, the mechanical clock, the glass lens, the printing press, the steam engine, the telegraph, electric power, wireless communications, antibiotics, and the transistor.

按照时间顺序排列，符合这些标准的发明是：指南针，机械钟表，玻璃镜片，印刷机，蒸汽机，电报机，电力，无线通信，抗生素和晶体管。

The methods and equipment for measuring and recording of Distance, Time, Speed, Altitude, Mass or other specific parameters, as well as equipment technical standards, shall be determined by each FAI Air Sport Commission and specified in the appropriate section of the Sporting Code.

用於测量和记录距离、时间、速度、高度、重量或其他特定参数之方法和设备，以及设备的技术标准，应取决於各 FAI 航空气运动委员会，并载明於运动规则的适当章节。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。