柴油机

Calculates the coordinates of the spindle and drive shaft and checking the center distance, determined department spindle must use dislodges the gear.

根据柴油机齿轮室盖的结构特点、加工部位、尺寸精度、表面粗糙度及生产率等要求，确定该机床为单工位卧式组合机床；为确保加工精度，采用&一面两销&的定位方案；为实现无级调速，安全可靠，选择液压滑台；根据零件的大小及被加工孔的位置确定主轴箱的轮廓尺寸；由加工工艺选择滚珠轴承主轴，通过计算扭矩确定主轴和传动轴的直径；齿轮的模数是通过类比法确定；齿轮齿数和中间传动轴的位置是由&计算、作图和多次试凑&相结合的办法确定；计算主轴、传动轴的坐标并进行中心距验算，确定部分轴上需采用变位齿轮；轴上的齿轮套、键等零件按轴号选取相应的标准件。

The information includes combustion, valve-open and valve-close information. But this signal also contains interfering noise, like exhaust noise and other noise eradiated from the other part of the diesel engine, and the frequency composition of useful signal and interfering noise are largely overlapped in the frequency band under 20 KHz.

但是提取的缸盖噪声信号中也含有柴油机工作时产生的排气噪声和机体其它部位辐射噪声等干扰信号，且干扰信号与有用信号的频率成分在20 kHz以下的频带内重叠在一起。

The hardware and software of humidifying equipment have been designed for ship compressor on the base of ultrasonic and Atmel 89C 51,and intelligent control of humidifying equipment has been also achieved.

基于超声波水雾发生器，利用Atmel89C51设计了用于船用柴油机增压加湿装置的硬件构成和软件，完成了加湿装置的智能控制。

When the diesel engine idles, engine oil pressure should not be less than 0.1MPa.

柴油机正常运转时，机油压力应在0.3～0.6MPa之间。

It is Modified by a electronically controlled engine, and work by diesel igniting the natural gas.

它是在电控柴油机的基础上改装而成的，采用柴油引燃天然气的方式来工作。

For a diesel engine, simulation was given to verify the performance of misfiring diagnosis.

针对某柴油机扭转振动模型的载荷识别问题，研究了所提方法的辨识性能。

Diesel engine obsoletes steamer.

柴油机取代了蒸汽机。

Through analyzing PM and NOX control methods separately, this paper presents the technical route of diesel PM and NOX combined control, and particularizes programs which has now been identified or are still in the research stage, in order to prove that the t technical route proposed reasonable.

本文通过分别对单独的PM和NOX的控制方法进行分析，提出了对柴油机PM和NOX进行综合控制的技术路线，并列举了目前已经得到应用或者还处于研究阶段的一些方案，以此来证明所提出的技术路线的合理性。

Through analyzing PM and NO_x control methods separately, this paper presents the technical route of diesel PM and NO_x combined control, and particularizes programs which has now been identified or are still in the research stage, in order to prove that the t technical route proposed reasonable.

本文通过分别对单独的PM和NO_X的控制方法进行分析，提出了对柴油机PM和NO_X进行综合控制的技术路线，并列举了目前已经得到应用或者还处于研究阶段的一些方案，以此来证明所提出的技术路线的合理性。

One engine that is rumoured to be in its final stages of development is an AMG V8 diesel.

其中已经进入开发最后阶段的是一台AMG V8柴油机。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。