柱

One is research on choice and optimization of clapboard material s of split columns, the other is research on technique of construction of split columns.

从两个方面对改善短柱特别是超短柱抗震性能的分体柱技术进行了进一步的试验研究，一是分体柱的隔板材料选择和优化的试验研究，二是分体柱施工工艺的试验研究。

Based on random signal theory, in order to quantitatively research drilling string by vibration measurement method, the article sketches out a new methodthe identification of drillstring system using the cross correlation function. Using input signal, and output signal, the impulse response of drill-string is obtained. Some problems...

在随机信号理论基础上，提出了一种用互相关辨识钻柱系统的新方法；结合输入信号和输出信号，利用钻柱系统的脉冲响应，讨论了钻柱的临界转速、钻柱共振、钻柱与井壁之间的相互作用、所钻地层岩性等钻井工程问题。

The factors included the type of extractant, the amount and the extraction times, the type of purified column, the type and dosage of eluviatant about the pre-treatment of the samples. The extraction was 3 minutes (13500rpm) of high speed homogenize extraction. 50mL acetonitrile as an extractant was acted on one time extraction. The florin silicon column was taken as the purified column. The extraction was eluted by 30ml 3:2 acetone - hexane and concentrated by nitrogen blowing under 50 °C water bath.The chromatographic separated conditions were studied applied the Agilent 6890 gas chromatographic apparatus and DB-17 capillary column(30m×0.25mm×0.25μm).

研究了提取剂种类、用量与提取次数，净化柱种类，淋洗剂种类与用量，提取方式与提取时间，柱温和柱流量等因素对油菜籽中有机磷农药残留提取、分离净化和色谱分离的影响，建立了采用高速匀浆提取方式提取3min13500rpm.min~(-1，以50mL乙腈为提取剂一次提取，以弗罗里硅柱为样品液净化柱，以30mL 3：2丙酮-正己烷为淋洗剂，在50℃水浴条件下用氮吹浓缩，气相色谱检测的油菜籽有机磷农药多种残留检测技术。

Based on the three dimensional viscoelastic integral constitutive relation of a propellant grain with the finite element method, the analysis about the thermo-viscoelasticity of solid propulsive agent column is presented.

基于药柱的三维线性热粘弹性积分本构关系，采用有限元法，对固体火箭推进剂药柱进行热粘弹性有限元分析，得出药柱在轴向过载作用下的变形结果和药柱内危险部位的位置，表明药柱具有明显的粘弹性特点。

The conclusions were as follows: theνO-H andνC=O IR absorption maxima shifted towards higher wave numbers after imprinting 17β-estradiol on TFMAA-co-TRIM copolymer with the red shift of theνO-H groups being apparent after precipitation polymerization for 16h while that forνC=O groups being observed after polymerization for 24h. A strong interaction between TFMAA and 17β-estradiol was confirmed by the high selectivity for 17β-estradiol, as indicted by the values of the separation factor of isomers of 17β-estradiol/17α-estradiol (2.28) and the imprinted factor (3.01). Particle diameter of TFMAA-co-TRIM polymer was between 300 nm and 1.5μm, which suited well for solid phase sorbent throughout at low column pressure. The recognition of imprinting TFMAA-co-TRIM polymer for sterol molecules was driven by enthalpy eluted with acetronitile, and low temperature was in favor of the separation of sterol structure analogues on imprinting column. TFMAA-co-TRIM polymer possessed of determinate anti-heat stability, with melting point beginning at 255.84℃, Tp=257.40℃, control TFMAA-co-TRIM polymer and imprinting TFMAA-co-TRIM polymer were respectively decompounded at 267.79℃and 343.11℃, and solid micro-extraction noddle prepared by the special polymerization also showed definite recognition for 17β-estradiol by GC/MS detecting at 270℃. By selection of various washing and elution solvents, elution reagents of close polymerization system were of more advantage in template molecules retention and recognition on molecularly imprinted solid phase extraction column. At a certain extent, progesterone, 17α-estradiol, 17β-estradiol and 4-androstene-3, 17-dione could be intercepted on the MISPE column. Especially, MISPE had high selectivity for progesterone, and imprinting TFMAA-co-TRIM polymer could achieve adsorption balance within 50 min by absorption kinetics test for 17β-estradiol. However, MISPE column showed better selectivity and enrichment property for 17β-estradiol than C18 and CSPE columns according to the data from HPLC and GC/MS analyses. Recovery of 17β-estradiol on MISPE column was up to 85.5% while when prime extracting solution of milk powder was sampled, the recovery of CSPE and C18 columns were 43.7% and 30.7%, respectively.

通过研究阐明：紫外聚合产物TFMAA-co-TRIM中的νO-H振动吸收峰在聚合16h后红移，νC=O振动吸收峰在聚合24h后红移；TFMAA-co-TRIM对雌二醇异构体的印迹因子达到了3.01，α为2.28，优于其它功能单体参与得到的聚合物识别特性；TFMAA-co-TRIM聚合物粒径介于300 nm至1.5μm之间，作为色谱固定相具有良好的通量和低的柱压；在乙腈流动相中，TFMAA-co-TRIM分子印迹固定相的分离过程主要被焓驱动，低温有利于分子印迹固定相分离甾醇结构类似物；TFMAA-co-TRIM分子印迹聚合物在255.84℃时开始熔融，Tp=257.40℃，聚合物CP的降解温度在267.79℃，MIP降解温度在343.11℃，制备的固相微萃取头初步经GC/MS 270℃的耐热性测定；不同的洗提溶剂筛选证明了选择接近聚合溶剂的洗脱体系更有利于MISPE发挥识别效应；分子印迹固相萃取柱对孕酮、17α-雌二醇、17β-雌二醇和雄烯二酮都具有不同程度的保留特性，可作为此类化合物的吸附材料，特别对孕酮强保留的富集特性，可作为孕酮的选择性识别吸附剂，其分子印迹聚合物对17β-雌二醇的吸附动力学测定显示在50 min内基本达到吸附平衡，具有作为传感器核心敏感材料的潜力；对比萃取奶粉中17β-雌二醇性能，MISPE柱比非分子印迹固相萃取柱和C18柱具有更高的保留，回收率依次为85.5%，43.7%和30.7%。

This issue discussed the mechanism of CGA-column flotation, and discussed the separation course of cyclone-static microbubble column, it concluded that the principle of flotation colurmn、 the principle and course of selfinduction、 pipe flotation and mineralization of microfoams、 the liquid state of column separation stage、 the principle of cyclone stage dynamics separation and strengthen the mechanism of cycle recovery of column.

本文对CGA-柱浮选的机理进行了探讨，论述了旋流静态微泡浮选柱的分离过程，包括浮选柱工作原理、自吸式充气原理与过程、管浮选与气泡的矿化、柱分离段的流体状态、旋流段力场分离原理和浮选柱的强化回收机制。

My company's main products are: Y28 series of 4 double-action hydraulic machine (35 to 1,200 tons a variety of specifications); Y98 series of tide-hydraulic machine; Y32 dynamic of 4-under-pressure hydraulic machine; YDK series on the framework of shifting hydraulic machine (1500 Tons, 2,000 tons, such as for aluminum pressure cookers, Bu Zhanguo complex at the end of the framework of large-scale hydraulic machine); Y33 series on the transfer of 4 hydraulic machine; Y31 series of double-column single-action hydraulic machine; Y38 series of 4 inverted hydraulic machine; Y41 series of single arm Hydraulic press; Y73 series of vulcanized rubber products; YK-bending series of hydraulic machine; high-precision Lvyou cars and various hydraulic stations, fuel tanks, according to customer requirements and design, manufacture Gezhongfeibiao hydraulic machinery.

我公司主要产品有：Y28系列四柱双动液压机（35吨至1200吨多种规格）；Y98系列水涨形液压机；Y32四柱单动下压式液压机；YDK系列框架上移式液压机（1500吨、2000吨等用于铝压力锅，不粘锅复底的大型框架液压机）；Y33系列四柱上移式液压机；Y31系列双柱单动液压机；Y38系列四柱倒置式液压机；Y41系列单臂液压机；Y73系列橡胶制品硫化机；YK系列弯曲木液压机；高精细滤油车以及各种液压站、油缸等，并可根据客户要求设计、制造各种非标液压机械。

The method for calculating the axial force, bending moment and bending deflection sucker rod string with centralizer is obtained applying compressionalto - shear buckling continuous beam - string theory- The design method for sucker rod string with weighting rod is presented in this paper, which takes the modified Goodman stress diagram as strength design principle and...

应用纵横弯曲连续梁柱理论得到了求解带扶正器的抽油杆柱的轴力、弯矩和挠度计算公式；以修正的Goodman应力图为强度准则，并考虑杆柱刚度条件，提出了水平井中抽油杆柱加重设计的方法。最后给出了某油田1口井的抽油杆柱设计实例，说明了该万法的正确性。

Since the rotary plunger pump piston at each stroke can randomly rotate constantly change with the pump plunger cylinder contact surface, so that circular plunger gradually wear uniform or scaling at the same time, sand from the plunger and pump barrel between discharge and resolved accumulation Materials abrasion caused by wear and serious positioning rod release.

自旋转柱塞抽油泵可使柱塞在每一冲程中随机转动，不断地改变柱塞与泵筒的接触面，使柱塞圆周逐渐均匀磨损的同时将砂粒或结垢从柱塞与泵筒之间排出，解决了磨蚀材料聚集所引起的严重定位磨损及杆柱脱扣

Since the rotary plunger pump piston at each stroke can randomly rotate constantly change with the pump plunger cylinder contact surface, so that circular plunger gradually wear uniform or scaling at the same time, sand from the plunger and pump barrel between discharge and resolved accumulation Materials abrasion caused by wear and serious positioning rod release.

自旋转柱塞抽油泵可以使柱塞在每冲程中随机转一下，不停地转变柱塞与泵筒的接触面，使柱塞圆周逐渐匀称磨耗的同时将砂粒或结垢从柱塞与泵筒之间排出，解决了磨蚀材料聚集所导致的紧张定位磨耗及杆柱脱扣。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。