板条

Companies from the United States, Germany, Sweden, the introduction of advanced production equipment and technology, the design annual production capacity of 100,000 tons aluminum, the main equipment has been put into deep well-type aluminum rod casting production lines, 500 tons -1650 tons of aluminum extrusion 9 production lines, 1600m / m aluminum casting production line 4, 1450m / m 2 of cold-rolled production line, 1500 m / m embossing plate production line, 1850m / m 2 cross-cutting production line, 2200m / m thick plate production line, 600m / m-1450m / m thick shear foil production line 3, 1450 m / m bending-straightening production line, 1000 * 5000m / m a CNC grinding machine, annealing furnace 20 tons of plate and strip, such as four-foil finishing equipment.

公司分别从美国、德国、瑞典引进先进的生产设备和技术，设计年产铝材十万吨，其中主要已投产设备有深井式铝棒铸造生产线两条，500吨-1650吨铝型材挤压生产线九条，1600m/m铝板铸轧生产线四条，1450m/m冷轧生产线两条，1500 m/m 压花板生产线一条，1850m/m横剪生产线二条、2200m/m厚板生产线一条，600m/m-1450m/m厚箔剪生产线三条，1450 m/m拉弯矫生产线一条，1000*5000m/m数控磨床一台，20吨退火炉四台等板带箔精整设备。

In the ferrous martensite transformations, the lath martensite of substructure with high-density dislocations is made up of the transformation basic-units with same orientations whereas the plate-shaped martensite with twin substructure is made up of the basic-units with different orientations.

本文根据铁基合金马氏体和贝氏体显微组织观察以及晶体学位向关系测定，提出板条马氏体、孪晶马氏体和贝氏体铁素体均由相变基元构成，相变基元具有切变形核长大的晶体学特征。

The bases were set deep down on the virgin rock. Only the visible pieces proofed of careful work. The pillars and pilasters were very finely made. The former were somewhat higher than the latter, and the four which supported the dome were 4.65 m. in size. They were topped by a moulding 25 cm. high. Their sides measured 143-145 cm.

圆柱的地基被深深地建筑在一座未开发的岩石上，只有显而意见的碎片能够证明这项精细的工程，石柱和方柱被建造的相当精致，前者比后者稍微高一些，四根支撑圆顶的石柱有4.65公尺高，石柱的顶端有25公分高的装饰板条，其侧面皆有143-145公分长。

Second, tree holes for long-term fix should not healing tree holes, we can surface at the hole for fixing lath to putty knife and Ma Gray closed (can also be used to install glass used in putty); And白灰Apply latex, pigments Noodles, Finally at the top pressure for fixing a piece of bark patterns or really bark, so that more natural appearance.

二、修补树洞对于长期不能愈合的树洞，我们可在洞口表面钉上板条，以油灰和麻刀灰封闭（也可用安装玻璃用的腻子）；然后再涂白灰乳胶，颜料粉面，最后在上面压树皮纹或钉上一块真树皮，以使外观更加自然。

This paper sets up the plastic energy consumption and tensile functions of the ideal rigid plastic steel wire and lath under large curvature tension bending .

建立了理想刚塑性钢条、板条在大曲率拉弯过程中的塑性耗能量函数与拉力函数。

The sites for nucleation of different phases are expounded in the weld metal of the low...

低碳低合金钢焊缝金属最理想的组织是获得大于65％的针状铁素体，其平均板条尺寸约为1 μm。

The MC nylon lath water-seal and wedge supporting slide block are adopted in the working anchor gate of the water transmission way of the Spring Lake s navigation lock, which has solved the problems of frequent operation of the anchor gate and the water-seal under condition of bearing bilateral pressure.

春天湖船闸输水廊道工作闸门采用了MC尼龙板条封水和楔形支承滑块，解决了闸门运行频繁、承受双向水压力情况下封水的问题。

Partially end-pumped slab laser using hybrid resonator is a favourable concept to scale high power with high beam quality in compact dimension.

部分端面抽运混合腔板条激光器可以在紧凑的空间内实现大功率高光束质量的激光输出。

Calculation of Induced Refraction Index in Heat Capacity Slab Laser.

热容型板条激光器的感应折射率计算。

In this paper,the problem of a mode Ⅲ crack in a functionally graded strip is studied with the assumption that the reciprocals of the shear modulus is a linear function in the thickness direction,while the Possion s ratio is kept constant.

作者假设功能梯度材料剪切模量的倒数为坐标的线性函数，而泊松比为常量，研究功能梯度板条的反平面裂纹问题。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失