条件方程

The primary contents are as follows:(1) Based on the fundamental seepage physical equation, the basic differential equation of saturated-unsaturated seepage in porous mediums has been deduced, in which the pressure head is the fundamental unknown quantity.

总体说来，本文主要从以下几个方面开展了研究：(1)由基本渗流物理方程出发，以压力水头为基本未知量推导多孔介质三维饱和—非饱和渗流微分方程，在此基础上分析了边坡在有降雨入渗条件下渗流的定解条件和计算模型。

In order to investigate the existence conditions of the robust optimal state feedback of uncertain system, we have to study the problem of GARE, that is the solution existence of the following equation PA+A'P+Q-PMP=0, Q=Q', M=M' In chapter 2, using some preliminary results and properties of the Riccati differential equation, we have established the sufficient conditions for the GARE problem.

在讨论不确定性系统LQL方法的状态反馈解的存在性条件时，引出了第二章讨论一般代数Riccati方程解的存在性问题，对一般Riccati方程 PA+A'P+Q-PMP=0，Q=Q'，M=M'第二章中先列举讨论了Q、M为正、负定各种情况下的实对称解的存在条件，然后着重研究了M、Q不定的情形。

A integral equation formulation is derived based on modified Green's operator with norm less or equal to one.

利用范数小于或等于1的修正Green算子得到各向异性地层中的新积分方程，由于满足压缩映射条件，该积分方程在任意参数条件下总是迭代收敛的。

The diffusion wave equation with the neglect of lateral discharge and backwater effect is resolved, and the analytical solution is represented by S-curve or duration unit hydrograph.

导出了具有分布式旁流的自由下边界条件的扩散波方程的解析解，这是对前人导出的不考虑旁流的自由下边界条件的扩散波方程解析解的补充。

The direct method of solution for non-normal type of singular integral equation with Hubert kernel is discussed. Their solution have form of integral and the condition of solution have form of the system of equations.

给出了具有Hilbert核非正则型奇异积分方程的直接解法，对核密度函数k在附加某些条件下，得出了方程积分形式的解和方程组形式的可解条件。

By means of the qualitative theory and method of delay differential equations, the weak conditions for the bound-edness of the system are obtained. By use of differential mean value theorem and computational techniques on delay differential equations, we show that the system is globally asymptotically stable under condition for the boundedness.

用时滞泛函微分方程的定性理论得到了系统有界的较弱的条件，并运用微分中值定理及有关时滞微分方程的计算技巧，我们获得了在系统有界这样弱的条件下就能保证系统全局渐近稳定的结论。

We know that asymptotically linear operator equations have negative solutions and sign-changing solutions besides positive solutions, in this chapter, we obtain the existence of this three kind of solutions in Banach space, and we can know the concrete place of these solutions.

第三章的目的就在于借助于不动点指数理论利用一致正条件讨论非线性算子方程变号解的存在性，同时研究了变号解与一对正负解之间的关系，在一定条件下我们证明了：若算子方程x=Ax存在一个变号解，则它的正解和负解必定成对出现。

In this paper,the numerical methods for the LS equation of three-dimensionaldetonation wave are introduced.

本文提出了在三维直角坐标系中爆轰波传播LS方程离散化方法，建立了相应的差分方程，研究了对不同形状炸药在多种起爆形式(点、线、面、散心、聚心)下初值条件的设定，以及各种边界条件的处理方法。

Proceeding from their oscillation differential equation, meeting the position conditions of borders and jointures between adjacent parts, this paper deducts the amplitude expressions of each part of whole system, and makes the stationary wave chart.

从微分方程出发，利用边界条件和各部分之间的连接条件，本文建立了超声传递系统各组成部分的振幅方程，得到驻波波形图。

The formula was established about calculating design parameters and technological parameters of ideal strip and bent strip in the period of forming. The thesis presented how to calculate the deformed area length and contact are radius of contact deforming between two elastic bodies on condition of the friction. The calculating formula of pinch force about plate-strip pinch mill was given and the results were analyzed that friction coefficient and radius of pinch rolls are very important for determining pinch force. Moreover, the rule of deforming and stress distribution of different 〓 ratio were gained on condition that the deforming was considered to be non-uniform distribution in the gap. The differential equations were got that calculate the displacements of large deflection of elastic cantilever rectangle plate with fixed end and the formula of the Finite Strip Method was conducted to study the regularity of mid-plane displacements, deformation and stresses for elastic-plastic large deflection bend of cantilever parallelogram plate with fixed or slidable end by integrating Prandtl-Reuss equation.

建立了一套完整的设计参数计算公式和在成型过程中理想带钢或具有月牙弯带钢的工艺参数的调整公式；在考虑摩擦力的条件下，对两弹性体接触变形过程中的接触变形区长度和接触弧半径用位移解法进行了研究，推导了板带递送机的递送力计算公式，从而得知在递送机设计过程中，应选择适当摩擦系数和辊身直径；另外，还从辊缝内带钢实际变形出发，分析了对于不同的〓值，带钢的变形规律及应力分布状况；建立了固定端悬臂矩形板弹性大挠度弯曲变形的控制方程，并且在对Prandtl-Reuss方程的积分处理的基础上，导出了固定端和滑动端悬臂平行四边形薄板的弹塑性大挠度的中面伸展位移、变形和应力的有限条元法公式，编写了Fortran语言计算程序，在各种参数条件下，对螺旋焊管成型过程变形规律进行了全面的分析研究，从而为螺旋焊管的生产和进一步的改进提供了理论依据。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。