条件分布

The authors analysed naked and transformed groups of fibrous brucite, wollastonite, chrysotile asbestos, sepiolite, palygorskite, clinoptilolite, crocidolite and diatomaceous earth mineral dust s by IR under acid and alkali etching and strong mechanical and polarized molecular interaction.

本文通过酸碱蚀、强机械力和极性分子等表面作用，利用红外吸收光谱手段分析7种重要矿物粉尘的表面基团裸露、转化过程，总结了矿物粉尘表面存在的基团类型及其表面活性位的分布及在不同环境条件下的转化，对讨论粉尘生物活性及矿物表面／细胞物理化学作用过程有重要意义。

The copolymerization of cycloolefin and α-olefin, and structure of the obtained polymer are significantly affected by the structure and symmetry of metallocene catalysts, electronic effect and steric hindrance of ligands.

着重介绍了加成聚合法中茂金属催化剂的结构对称性、配体的电子和体积效应、反应条件等对聚合活性、产物组成与序列分布及相关热性能的影响。

The copolymerization of cycloolefin and α-olefin,and the structure of the obtained polymer are significantly affected by the structure and symmetry of metallocene catalysts ,electronic effect and steric hindrance of ligands.

着重介绍了加成聚合法中茂金属催化剂的结构对称性、配体的电子和体积效应、反应条件等对聚合活性、产物组成与序列分布及相关热性能的影响。

Since the multiple scattering should be considered, the scattering problem of many-cylinders is more complicated than single cylinder. By using scattering matrix method to solve the scattering problem of many-cylinders, first we have to express the incident fieldand scattered field by special function（for example, Bessel function and Hankel function）under cylindrical coordinate, then use the addition theorem of special function to get a linear system of equations to relate the incident field coefficients and scattered field coefficients. The incident and scattered field coefficients for every cylinder can be solved from the linear equations by matching electromagnetic boundary condition pointwisely.

单颗圆柱散射体的散射场解析解很早就被解出，而多个圆柱阵列的散射场问题因为涉及到入射光在圆柱与圆柱间的多重散射，故散射行为较单颗圆柱的散射复杂，因此圆柱阵列的多重散射问题需要利用加法定理来处理；散射矩阵法的主要精神即是先用圆柱座标下的特殊函数对平面波和圆柱散射体的内外域电磁场做无穷级数展开，再藉由特殊函数的加法定理将所有圆柱散射体的展开中心移到同一个展开中心，最后可以得到一组连结整个散射系统的入射电磁场系数及散射电磁场系数的线性方程组，将该组线性方程配合电磁场在散射体边界的连续条件，便可分别求出圆柱阵列中各个圆柱体的内部电磁场与外部散射场，再利用线性叠加原理即可求得整个圆柱系统的全域电磁场分布。

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

With boundary conditions,pressure distribution and the damping force on the plate can be found by solving the differential equation.

结合边界条件求解该方程可以得到各种压膜阻尼结构中的阻尼压强分布和阻尼力。

By direct microscopic observations of thin section of Inada granite in the heating process, decrepitation temperature of fluid inclusions in quartz and feldspar was determined to be in a range from 170℃ to 550℃, and thermal microcracking due to the decrepitation of the fluid inclusions was ascertained.

通过常温及高温显微镜观察，查明了稻田花岗岩中流体包裹体的初始分布状态，并发现在高温条件下，由于流体包裹体的爆裂而导致花岗岩中微小裂纹的形成。

Numerical examples are studied to demonstrate the accuracy of the proposed method and to investigate the distribution of the optimal stiffness of the elastic restraints, the deformation of the elastic restraints and deflection of the stiffened plate for stiffened plate with different number of stiffeners, different cross section of stiffeners and different thickness of plate.

本研究利用牛顿法提出一个数值程序以求得使目标函数有最小值且满足拘束条件的弹性支承刚度，即求得最佳化的弹性支承刚度。本研究以数值例题探讨不同加劲板之最佳化的弹性支承刚度，弹性支承变形的分布及加劲板的最大挠度。

To accelerate the widespread of Synchronous Chip Seal and improve the operation quality of Synchronous Chipsealer, key techniques which influence the operation quality is studied detailedly, including the control of distributing quality, the dynamics characteristics of hydraulic system and the spray characteristics of asphalt nozzle of Synchronous Chipsealer.1 The factors which influence Synchronous Chip Seal quality are studied. Fiducial probability of simultaneous distribution density is advised to be used in evaluating the distribution bias and standard deviation of asphalt and aggregates simultaneously, which is more advanced than the single index evaluation method used before.2 The volume efficiency formula of asphalt pump is revised after analyzing the data of volume efficiency with mathematical statistics, which is helpful to match the asphalt spray system and control the flow out of asphalt pump accurately. With equation deduction and experiment, dynamic of hydraulic system used in Synchronous Chipsealer is studied, which lay the theory foundation on improving the stability and efficiency from design and controlling.4 Simulation on hydraulic system used in Synchronous Chipsealer is done with AMESim; the results indicate that multi-circle parallel connected hydraulic system with constant pressure power is better than that with load-sensing pressure power at present, because the latter will oscillate when the multi circles work at the same time. This conclusion has been proved during the debug of Synchronous Chipsealer.5 Asphalt nozzle characteristics, such as flat jet shape, flow distribution, are studied with experiment, the results indicate that cross quality of asphalt distributing is not increased linearly follow the increase of fan overlap level, the best point usually exists between two whole overlap level, asphalt distributing quality is better than±4% at the 2.5 overlap level, meets the superior specified in standard; The distribution quality of Synchronous Chipsealer can be increased by spray asphalt of different flow rang with nozzle of different diameter

为了加快同步碎石封层技术的推广，提高同步碎石封层设备的作业质量，本文对同步碎石封层设备作业质量的影响因素与控制方法、液压系统的动力学特性和沥青喷嘴的喷洒特性等关键技术进行了深入细致的研究：1研究了影响同步碎石封层作业质量的因素，提出了采用联合密度分布置信概率对同步碎石封层中沥青洒布量和碎石撒布量的系统偏差和标准差指标进行综合评价的方法，克服了传统评价方法只能对单一指标进行评价的缺陷；2采用数理统计的方法，研究了沥青泵的容积效率特性，修正了沥青泵容积效率公式，为沥青喷洒系统的匹配和沥青泵出口流量的精确控制提供了依据；采用数理方程推导与试验相结合的方法，研究了同步碎石封层设备液压系统的动力学特性，为从设计和控制的角度提高同步碎石封层设备液压系统的稳定性和效率奠定了理论基础；3运用AMESim软件对采用负载敏感控制和恒压控制的两种同步碎石封层设备液压系统进行仿真，结果表明：负载敏感控制的并联液压系统在多回路同时工作时，由于液压泵排量控制参考压力不稳定，容易引发液压系统振荡，恒压控制的并联液压系统是目前技术条件下比较理想的同步碎石封层设备工作装置驱动方案；该结论亦通过同步碎石封层设备装机试验得到了验证。4采用试验的方法对沥青喷嘴的喷洒特性进行了研究，结果表明：沥青洒布的横向精度并不是随着喷洒扇面重叠度的增加线性增加，其最高点通常出现在二个重叠度之间的"半重叠位置"，"2.5重叠"洒布时，沥青的横向洒布精度≤±4%，可以达到国家相关标准中的优级标准；同步碎石封层设备还可以根据不同洒布量情况下的流量需求，采用不同通径的喷嘴进行喷洒，提高沥青洒布精度。

By simulation and derivation,the degree of nodes in this model...

通过计算机模拟和公式推导，该模型中节点的度分布显示出幂律尾部的特性，而且其衰减指数在一定条件下与实证研究结果是一致的。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。