杆

With the screw rotation and meshing, the sealed space in the pump suction side evolving to inhalation chamber inclose one of the liquid, and from inhalation of room along the screw axis moved continuously push from client, will be closed in the space continuous discharge of liquid, like a nut in the thread when he was constantly turning the situation to move forward, this is the basic working principle of the screw pump.

随着螺杆的转动和啮合，这些密封空间在泵的吸入端不断形成，将吸入室中的液体封入其中，并自吸入室沿螺杆轴向连续地推移至排出端，将封闭在各空间中的液体不断排出，犹如一螺母在螺纹回转时被不断向前推进的情形那样，这就是螺杆泵的基本工作原理。

But with its variety and specialization , three-axial non-instaneous envelope method had not meet needs. So four-axial non -instaneous envelope method was set forth firstly in this article, which is based on three-axial non-instaneous envelope and spiral rod compressor rotator speciality.

然而随着螺杆应用范围的扩展，螺杆型线不断复杂化、多样化，三自由度无瞬心包络铣削法已不能满足部分型线的加工要求，为此本文在三自由度无瞬心包络铣削法的基础上，针对螺杆压缩机阴阳转子的特性，在国内首次提出四自由度无瞬心包络铣削螺旋曲面的新方法，赶超国际螺旋曲面加工技术水平，具有重要的理论和现实意义。

3D finite element model of concrete pavement in transverse joint with dowel bar s or without dowel bar s is established by 3D finite element numerical analysis method.

建立接缝无传力杆及设传力杆时水泥混凝土面层结构的三维有限元模型，运用数值分析方法，分析接缝处水泥混凝土面层的荷载应力、弯沉值和弯沉差，研究了地基模量、传力杆直径对荷载应力及弯沉差的影响规律，并对条件相同的计算结果进行了对比分析。

If as a result of body shell keycap stuck with the key causes of the "key card" failure, may be key in the cap and put a gasket between the pads can be used稍硬some plastic (such as floppy disk jacket abandoned) made, its size is equal to or slightly larger than the key body size, and location by the rod through the ammonium can open a free passage under the square hole, in accordance with its set of poles, the plug cap; use this pad chip cap with the key body to prevent stuck, you can repair button; If as a result of spring fatigue, shrapnel resistance causes large card key failure, then the Special button to open the body, a little stretching to restore flexibility to reset the spring; Remove the key precursor to the resumption of shrapnel.

若是由于键帽与键体外壳卡住的原因造成"卡键"故障，则可在键帽与键体之间放一个垫片，该垫片可用稍硬一些的塑料做成，其大小等于或略大于键体尺寸，并且在按杆通过的位置开一个可使铵杆自由通过的方孔，将其套在按杆上后，插上键帽；用此垫片阻止键帽与键体卡住，即可修复故障按键；若是由于弹簧疲劳，弹片阻力变大的原因造成卡键故障，这时可特键体打开，稍微拉伸复位弹簧使其恢复弹性；取下弹片将键体恢复。

Hop off the jump or transition, turn 90 degrees, and land on the rail square with the rail directly under the center of your boot sole.

上杆的时候，确保雪板和铁杆成90度角，并且和铁杆接触的部位应该落在板底的中心位置。

Compared with three familiar one-class methods,it is found that the SVDD has stronger classification ability and higher efficiency,which can distinguish the normal and abnormal screws ideally,and provides a new method for light-rail's screws fault diagnosis.

通过与常见的三种单值分类方法比较，表明SVDD分类器具有很好的分类效果和计算效率，能较好地区分正常螺杆和非正常螺杆，为轻轨锚固螺杆故障检测提供了新的诊断方法。

The principle of minimum potential energy was used to derive the governing differential equation and corresponding boundary conditions.

分析了压杆屈曲时的几何变形条件，导出了压杆的曲率、变形能和各项外力势的表达式，用最小势能原理导出压杆失稳的微分方程和边界条件。

The natural twist vibration equation is set up by making use of the constitutive relation of nonlinear material.

利用非线性材料的本构关系，建立了非线性材料圆杆的扭转固有振动方程，然后采用傅立叶级数法求得了圆杆扭转固有振动的所似解，通过实例计算讨论分析了非线性材料圆杆的扭转固有振动特性。

A new method called generalized displacement method, using new structural model taking into account the deformation of the nodal point and avoiding the disadvantage of stiffened nodal point model, is proposed here to calculate the displacement and the stress in adjecent point of thin-walled structure.

一、薄壁杆件结构的计算模型对金属薄壁杆件组合结构用有限元法计算时，遇到的一个困难是不同截面形状的薄壁杆件在连接点处由翘曲引起的轴向位移不协调。

As a result,the tooth profile equations, helix angle equations,limit curve equations and induced normal curvature equations for worm and internal gear are obtained.

介绍了一种新型的传动机构超环面行星蜗杆传动，运用啮合理论的包络法建立了这种传动中行星轮与蜗杆、行星轮与内齿轮啮合的基本方程，进而得到了蜗杆和内齿轮的齿面方程、螺旋升角方程、界限曲线方程及诱导法曲率方程等。

And if officials on the take are not parroting the opinions of these companies, what can we suppose the money they receive is for?

如果受贿的官员不鹦鹉学舌般地复述这些公司的看法，那他们所接受的钱又能用于什么目的呢？

Love them, and love you too, Pitcher.

爱他们，也爱你，投手。