机轴
- 与 机轴 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The e axis cards and membership cards making machine business card printing and membership card making registration are electrically direct drive to each plate cylinder to correct version of the drum location, you do not receive the traditional gravure press roll due to compensation arising from the wrinkling.
电子轴制卡和会员卡制作机的制卡和会员卡制作套准是通过电气直接传动至每个印版滚筒来纠正版滚筒位置而实现的,所以不会出现传统凹印机由于补偿辊所引起的打褶现象。
-
Its work is the process of spraying by the pulp put out the warehouse I expected or high water concentration pulper, as well as the initial concentration of the pulp slurry into the mouth of the double helix squeeze machine feed the population through the right and left of the screw shaft Reverse spin, by the end of the pulp to be on the other side.
其工作过程是纸浆由喷放仓的出料口或高浓水力碎浆机的以及经初步浓缩的浆料出浆口进入该双螺旋挤浆机的进料口,通过左、右螺旋轴的反向旋转,纸浆由一端被推向另一端。
-
Gear shaft of converter reductor are fractured during test running.
某炼钢厂一台与250 t转炉相配套的减速机在试运行中,减速机齿轮轴发生断轴事故。
-
The products combined more than 10 series gearboxes with thousands of specifications, which include R Rigid tooth flank helical gear units, S Helical-worm gear units, K Helical-bevel gear units,F Parallel shaft helical gear units, T Spiral bevel gear units, SWL, JW Worm screw jack H.B Rigid tooth flank gear units, P Planetary gear units, RV Worm reducer. These products are slowdown drive device that is commonly adopted in the field of current international industrial transmission.
公司生产R系列斜齿轮减速电机,S系列斜齿轮-蜗轮减速电机,F系列平行轴斜齿轮减速电机,K系列斜齿轮-锥齿轮减速电机, X 系列摆线针轮减速机, T系列螺旋锥齿轮转向箱,H、B系列标准工业齿轮箱,蜗轮丝杆升降机机,RV系列蜗轮蜗杆减速机等十余个系列,数千种规格的产品,是目前国际上工业动力传输领域最普遍采用的减速驱动装置。
-
By means of finite element method, we analyze the stress distributing and fatigue state of tube mill hollow shaft of some factory applied self-produce FE soft ANSYS, provide the bases for estimating working circumstance of tube mill of running state.
利用有限元分析方法,应用自制的有限元软件ANSYS程序,对某厂管磨机出料中空轴的应力分布及疲劳状态进行分析研究,从而为判断运行状态中管磨机的工况提供依据。
-
150HP-300HP screw air compressor rotor is the German GHH-RAND joint shaft type unit,adopts the third generation asymmetrical dentate 5:6 rotors,The major axis is more reasonable than the choice, the tangent speed of rotors is only 30-36m/s, is far lower than that———60m/s of common air compressors, it keeps 0.003INCH between rotors that will not abrase forever, the space between teeth dropping variance is small, so the backflow loses is slight, Enhances10-12% kf the efficiency compared to the 4:6 dentate, save power 20%, adopts the Swden SKF bearing.
150HP-300HP)螺杆机转子为德国GHH-RAND联轴式机组,采用第三代非对称齿型为5:6的转子,长径比选择合理,其转子的切线速度仅为30'36m/s,远低于一般空压机60m/s 的切线速度,转子之间保持0.003INCH间隙永不磨损,齿间落差小,故回流损失小,比4:6齿型提高效率10-12%,省电20%,采用瑞典SKF轴承,极大延长了主机的寿命。
-
Br/br/Adopts the GHH-RAND remarkable mainfrane br/(150HP-300HP) screw air compressor rotor is the German GHH-RAND joint shaft type unit,adopts the third generation asymmetrical dentate 5:6 rotors,The major axis is more reasonable than the choice, the tangent speed of rotors is only 30-36m/s, is far lower than that60m/s of common air compressors, it keeps 0.003INCH between rotors that will not abrase forever, the space between teeth dropping variance is small, so the backflow loses is slight, Enhances10-12 kf the efficiency compared to the 4:6 dentate, save power 20, adopts the Swden SKF bearing.
采用GHH-RAND卓越主机br/(150HP-300HP)螺杆机转子为德国GHH-RAND联轴式机组,采用第三代非对称齿型为5:6的转子,长径比选择合理,其转子的切线速度仅为3036m/s,远低于一般空压机60m/s 的切线速度,转子之间保持0.003INCH间隙永不磨损,齿间落差小,故回流损失小,比4:6齿型提高效率10-12,省电20,采用瑞典SKF轴承,极大延长了主机的寿命。
-
By the requirement of the wagon wheel descale technics and manufacturing which is needed before detection,a new type automatic synchronizing deruster was developed to realize these functions.
根据铁路货车轮对除锈探伤的工艺和生产要求,研制了新型的同步除锈机。新除锈机采用机械传动方式驱动除锈转刷对轴身除锈,同时通过单个液压缸调整安装角度的方式对防尘板座除锈。该系统采用可编程序控制器实现了自动控制
-
The safety stitch overlock machine makes an additional row of stitching and uses 4 to 5 spools of thread.
安全线迹拷边机产生的线迹比拷边机的线迹多了一排,用4~5个线轴。
-
The safety stitch overlock machine makes an additional row of stitch ing and uses 4 to 5 spools of thread.
安全线迹拷边机产生的线迹比拷边机的线迹多了一排,用4~5个线轴。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。