机器人

EMC2 is a software system for computer control of machine tools such as milling machines, lathes, plasma cutters, robots, hexapods, etc.

EMC2是基于 PC 机的软件系统，用于控制铣床、车床、等离子切割机、机器人、昆虫机器人等。

This paper optimized take-off posture of hopping robot by applying inertia matching ellipsoid and directional manipulability.

提出了一种跳跃机器人起跳运动优化方法，分析了跳跃机器人惯性匹配与跳跃性能的关系。

The anti-interference design of pipe welding robot is the key of pipe welding process stability,in which the one of main effects is the anti-interference circuit design of pipe welding robot.

在电弧强干扰下，管道焊接机器人抗干扰设计成为管道焊接过程稳定性关键，其中管道焊接机器人抗干扰电路设计是主要影响因素之一。

Meanwhile, a new approach is also proposed to increase the machining accuracy by using virtual knife tool center point together with a technique of robot system error pre-compensation.

同时，提出一种使用虚拟刀具工具中心点和预补偿机器人系统误差的方法，提高了机器人的加工精度。

In this project, a set of universal master controller was developed, which is integrated with a master manipulator to be a mas.

本论文以山东科技大学机器人研究中心承担的国家863计划项目&配电作业带电作业机器人&为背景，研制了一套通用型主手控制器，它与主手本体集成为主手控制系统，可以在不同的系统下控制不同的从手运动。

As part of the 2007 RoboCup in Atlanta, Georgia, a new fleet of bots debuted in the Nanogram Demonstration competition in July.

今年7月，在佐治亚州亚特兰大市举行的&2007机器人足球世界杯&毫微克演示比赛中，一支由机器人组成的新球队首次亮相。

While the bots measured up to a few hundred micrometers in length, they were considered "nanoscale" because they weighed from only a few nanograms to a few hundred nanograms.

虽然这些机器人身体全长达几百微米，但它们仍被视为&纳米级&机器人，因为它们只有几毫微克到几百毫微克重。

With a whir and a flash of lights, a robot whizzes to the restaurant table and takes a customer's order, while a second races to another table to deliver plates of steaming food.

一台机器人身上闪著光，呼地奔向餐桌帮客人点菜，此时另一台机器人冲向另一桌客人，端上热腾腾的食物。

By utilizing stage to stage control method, the walking robot realizes static gait walking, the in-pipe robot can walk in the pipeline forward and backward, up and down, left and right, can pass"L"shape and"T"shape pipe connector, can pass in and out pipe nozzle.

采用基于马氏体相变的分阶段驱动控制方法，步行机器人实现了静步态行走，管内机器人实现了管内前后、上下、左右全方位行走，可通过&L&型、&T&型管接头，可进出管口。

We should know the parameters of the robot, such as: link lengths, masses, inertia tensors, distances between joints, the configuration of the robot, and the type of each link.

我们应该知道参数的机器人，如：连接长度，群众惯性张，距离关节配置机器人，类型每一个环节。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。