末尾的

Cyclic Redundancy Check Cyclic Redundancy Check method of principle as follows :(1) The data to be sent to the corresponding polynomial p.

令T=M+R，采用模2运算，T所对应的数据是在原数据块的末尾加上余式所对应的数据得到的。(6)发送T所对应的数据。

Choose rotting away at the end of it all,pishing your last in a miserable home,nothing more than an embarassment to the selfish,fucked up brats you spawned to replace yourself.

选择在这一切的末尾烂掉，最后在一个破破烂烂的家里遭儿女唾弃，当初你用精子弄出他们来代替你，现在对这些自私的、满不在乎的小子们来说，你只是一个老厌物。

Choose rotting away at the end of it all, pishing you last in a miserable home, nothing more than an embarrassmentto the selfish, fu*ked-up brats you have spawned to replace yourself.

选择在这一切的末尾烂掉，最后在一个破破烂烂的家里遭儿女唾弃，当初你用精子弄出他们来代替你，现在对这些自私的、满不在乎的小子们来说，你只是一个老厌物。

Choose rotting away at the end of it all, pishing you last in a miserable home, nothing more than an embarrassment to the selfish,***ed-up brats you have spawned to replace yourself.

选择在这一切的末尾烂掉，最后在一个破破烂烂的家里遭儿女唾弃，当初你用精子弄出他们来代替你，现在对这些自私的、满不在乎的小子们来说，你只是一个老厌物。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

An illustrated word list in the back of the book provides extra support for the newest readers!

在书的末尾处还有一个带图片的单词列表，对于那些刚刚接触阅读的小朋友来说，这个单词表会起到很大的作用！

One thing it says is that it returns -1 at the end of the file (not a very nice protocol in my view, but I guess that makes it more natural for C programmers).

有一件是它应该在文件的末尾处返回-1，（按我的观点，这不是很美妙的协议，不过，我估计这会让c程序员觉得更自然），让我们测试它，我的文本编辑器告诉我文件有141个字符，所以，测试如下所示

The use of an X at the end of a letter to signify a koss goes back to the Middle Ages,when an illiterate person signed his or her name to marked documents and contracts with an X (which in church lore stands for Christ)and kissed the mark in the pressence of witnesses to affirm his or her sincerity .

在信的末尾用X代表吻，这一做法可追溯到中世纪。那时候，不识字的人用X在文件或合同上签名，并且当着证人们的面吻这个记号以表明自己的诚挚。吻和X这个十字形符号变成了同义词。

At the end of the article, I will show you how to find permutations of a smaller set from a bigger set, using both next_combination and next_permutation.

在文章的末尾，我将告诉你如何找到一个更大的一套一套的一个较小的置换，同时使用next_combination和next_permutation。

Before him was the line of unfortunates whose beds were yet to be had, and seeing a newcomer quietly edge up and take a position at the end of the line, he decided to do likewise.

他面前站着一队还没有得到铺位的不幸的人，当他看见一个新来的人悄悄地挤上来，站到队伍的末尾时，他决定也照着做。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。