末尾

Bytes caused the system to read past the end of file, finding zeroes with

字节导致系统读取过的文件的末尾，找到与零

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

She is always only in the bud where roses bloom, because ...

不对，我觉得应该把only 放在第一个小句的末尾，即bloom。

An illustrated word list in the back of the book provides extra support for the newest readers!

在书的末尾处还有一个带图片的单词列表，对于那些刚刚接触阅读的小朋友来说，这个单词表会起到很大的作用！

Making the button stack-based would fail, as the AppWindow does not have a valid HWND before the end of the AppWindow's initializer list, so it is impossible to construct the button in the initializer list.

制作按钮基于堆栈将失败，因为AppWindow没有前AppWindow的初始化列表的末尾一个有效的HWND，所以是不可能的建设中的初始化列表按钮。

One thing it says is that it returns -1 at the end of the file (not a very nice protocol in my view, but I guess that makes it more natural for C programmers).

有一件是它应该在文件的末尾处返回-1，（按我的观点，这不是很美妙的协议，不过，我估计这会让c程序员觉得更自然），让我们测试它，我的文本编辑器告诉我文件有141个字符，所以，测试如下所示

The tradition of cartwheeling dates back to the wedding of Jan Wellem when a wheel of his carriage grew loose.

当时他的一个马车轮松脱，据说一个10岁的男孩紧紧地抓住它，并且把它滚到游行队伍的末尾。

One night towards the end of the trip, I knocked on my mum's door before she went to bed.

在这个旅程的末尾的一天晚上，我在我妈妈睡觉之前敲开了她的房门。

For example, if you wish to highlight comments starting with double dash until the end of the line with gray italic font on transparent background, you would do the following

例如，如果你想强调的评论双破折号开始，直至与灰色的透明背景斜体行的末尾，你会做以下操作

Do you think you can find an eighty-five?

你看能弄到一张末尾是八五的吗？

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷