未冷却的

In this paper, the relations of operating parameters such as coolant temperature, engine speed, throttle valve opening and spark advance angle with unburned hydrocarbon emissions due to the presence of combustion chamber deposits in spark ignition engine are investigated both theoretically and experimentally.

本文从实验和理论两个方面来系统地研究火花点火式发动机燃烧室沉积物处未燃碳氢排放浓度随冷却水温、发动机转速、节气门开度和点火提前角等运转参数的变化规律。

In sintering process, for melted mineral fines bind unmelted core ores when cooled, the self-intensity of binding phase in iron ores is one of the basic indexes to estimate sintered binding status.

在铁矿粉烧结过程中，熔化的矿粉在冷却过程中起着粘结周围未熔矿粉的作用，因此这一粘结相的自身强度是衡量烧结矿固结状况的重要指标之一。

The results show that carbonitride of V dissolve in large quantities at the heating-up temperature range of 860~900℃, and the carbonitride of Ti dissolve gradually over 900℃; the precipitated phase increase gradually and the size decrease with the gradual decrease of c.

针对V-Ti微合金钢，采用透射电镜分析了不同加热温度下微合金碳氮化物的溶解，未形变与形变奥氏体在不同冷却温度下碳氮化物的析出。

Test the warp and weft heat shrinkage rate of unfusible interlining and fusible interlining silk fabric under the same temperature and different times,also under different temperature conditions.

在同一温度不同时刻以及不同温度条件下分别对未粘衬及粘着不同衬料的真丝面料的经、纬向热缩率进行了测试，结果显示，面料本身性能、熨烫冷却后的放置时间、熨烫温度、熨烫粘合温度及粘合衬的种类均会影响面料的热缩率。

It is necessary for two kinds of controlled cooling processing to possess air cooling phase to separate ferrite from austenite, and, by means of this, polygonal ferrite forms, the carbon concentration of the retained austenite untransformed increases and results in the stability of retained austenite increased.

在二种冷却方式轧后控冷的过程中，必须有一个α/γ二相分离的空冷阶段，使多边形铁素体形成，未相变奥氏体中碳浓度增高，其稳定性增强。

The frequency about 16KHZ the permeabIe feverΦ60 about work Piece,mayweld many kinds of hard aIloy tools 1、the standard Piece.the faslener heat upset 2、drill rod steel,drill rod utensil drawing-back,forge,squeeze the warmup waiting 3、Welding of diamond saw.drilling tool 4、Bit,coal aiguille,rivetting the pole aiguille,welding of the pick 5、Lathetool,planer tool,milling cutter and welding of different woodwork cutters

目前使用感应加热设备的用户因自身条件各不相同对于冷却水系统重视不够，未按规定使用纯净水而使用井水或自来水，造成冷却部位结垢，局部温度升高严重影响电器元件的可靠性和使用寿命。

Because letoff was combined with two kinds of material has not been immediately strong adhesion strength, a composite fastness isn't very good, some earlier largening letoff tensility urasennichi letoff skinpass compact, shrinkage, after cooling, composite fastness will be all right.

由于在收卷时被复合在一起，两种材料还未立即产生很强的粘合力，复合牢度不太好，些时适当地加大收卷张力可以使收卷平整紧凑，不容易产生收缩，经冷却定型后，复合牢度就会好一些。

Due to very short time in welding and the large cooling rate of the joint, the transformation of austenite in the nugget suppresses, and the microstructure of the nugget refines remarkably, the microstructure of HAZ uncharges.

由于储能焊极短的焊接时间和大的冷却速率，熔核中奥氏体组织来不及长大，使得接头组织得到显著细化，热影响区组织未发生明显变化。

The prograde path was related to the magmatic accretion in arc settings, indicating the existence of an arc setting during the MesoproterozoicNeoproterozoic period. The retrograde near-isobaric cooling path after the peak metamorphism reveals that rapid erosion did not occur and sustained heat supplies from the upper-mantle were maintained after magmatic accretion in the Yuanmou area.

该轨迹的进变质阶段与岛弧地区的岩浆增生过程密切相关，指示元谋地区在中-新元古代期间(1.0～0.85Ga)存在岛弧构造环境；峰期之后的近等压冷却退变轨迹表明该地区未经历强烈的剥蚀，并可能有深部热流的持续供给。

Cooling and rescanning of all resistant starch samples did not show residual or new peaks because of extrusion, which increased solubilization and accessibility of amylose to chemical additives.

将所有的抗性淀粉冷却后再扫描未显示任何新的峰，这说明挤压能提高溶解性以及直链淀粉对化合物的接近性。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。