有接缝的

Finally, the idea of using new numerical method such as Discontinuous Deformation Analysis and Numerical Manifold Method to simulate the joint of CFRD is proposed, which can make guidance on the design and calculation of CFRD built on thick alluvium deposits.

提出引进新的数值方法，如不连续变形分析方法和数值流形方法，来模拟和计算面板坝接缝变形的设想，对深覆盖层上面板堆石坝的设计和计算有指导意义。

And then take a look at the edge of the chassis plate is smooth, whether the sharp mouth, burr, etc., and now the edge of the majority of chassis fold have done a deal, but some cheap chassis obviously only part of the fold so to deal with more hidden places on the jerry-built, so the selection must take note of the time look at the corners and joints, such as such as not easy to arouse attention.

然后看一看机箱板材的边缘是否光滑，有无锐口、毛刺等，现在大多数机箱的边缘都做了折边处理，但是有些廉价机箱仅在比较明显的部分做了折边处理，较为隐蔽的地方就偷工减料了，所以挑选的时候一定要注意看看诸如边角以及接缝等不容易引起人们注意的地方。

Standard of ornamental design acceptance of work: Ornamental design project is finishing dry hind, just can check and accept; Check and accept ornamental design project, whether does the breed that should check ornamental design, norms, design accord with design requirement; Ornamental design should be installed firm, its quality asks to reach tolerance, should accord with: The level of form ornamental design and perpendicular tolerance, every meters must not be more than 5 millimeter, must not be more than 3 millimeter endlong; The tolerance of position of alone ornamental design, must not be more than 10 millimeter; Ying Guangjie of ornamental design surface, design clarity, juncture rigor, must not interstitial, warp, edge damage drops the blemish such as horn; Back up spends exterior Ying Guangjie, design clarity, without break.

花饰工程验收标准：花饰工程完工并干燥后，方可验收；验收花饰工程，应检查花饰的品种、规格、图案是否符合设计要求；花饰应安装牢固，其质量要求及允许偏差，应符合：条形花饰的水平和垂直允许偏差，每米不得大于5毫米，全长不得大于3毫米；单独花饰位置的允许偏差，不得大于10毫米；花饰表面应光洁，图案清晰，接缝严密，不得有裂缝、翘曲、缺棱掉角等缺陷；裱花表面应光洁，图案清晰、无裂缝。

The high quality of the fossils also allowed the team to examine the joint surfaces on many of the fin bones, concluding that the shoulder, elbow and wrist joints were capable of supporting the body, like limbed animals.

许多高质量的化石也允许小组验证接缝表面飞翅骨头，认为，肩膀、手肘和桡腕关节是能支持体构，象有肢的动物。

Barrel lining is equipped with solid model of hard alloy sheath, which enhances the strength of the sheath body and completely overcomes the splintery problem at the seam crossing between bush splices.

机筒内衬有整体式硬质合金套，提高了套体的强度，完全克服了拼接衬套接缝处易裂的问题。

The main characteristic contents are as follows:(1) Strains, displacements, reaction of soil, natural frequencies and main mode shapes et al are examined in the static and dynamic experiments of slabs on foundation and doweled slabs of concrete pavement.

1进行了混凝土地基板、接缝板的静、动力试验，主要测试内容包括应变、挠度、土基反力、频率、主振型等，从中得出了一些有意义的结论。

The roof with elastic rubber is no joints which could be expose in the air without protection.

产品为白色液体橡胶、现场浇筑后，形成一层白色或铝灰白色的弹性橡胶，该橡胶屋面无接缝。直接暴露于空气中，有强的抵抗紫外线能力。

She was the first to create a one-seam dress, a challenge couturiers such as Balenciaga, Azzedine Alaa and Yohji Yamamoto have attempted to better since.

她是第一个创造&一接缝&服饰的人，是一个有挑战的女服装设计师，试图比巴伦夏加，Azzedine莱亚和山本耀司更优秀。

Not superstition paint packaging, the "green" word, it is necessary to seriously examine the quality of the products qualified testing; Observer metal containers have broken the joints Department, leakage; Explicit attention to the iron bucket marking is complete.

不要迷信涂料包装上的&绿色&二字，要认真看清楚产品的质量合格检测报告；观察铁桶的接缝处有没有锈蚀、渗漏现象；注意铁桶上的明示标识是否齐全。

Wear well-fitting socks, without a thick toe seam, made of a material that wicks moisture away from the skin, such as acrylic or CoolMax.

穿合适的袜子，不要有粗糙的脚趾接缝，袜子的材料能吸走皮肤的湿气，例如丙烯酸纤维或者 CoolMax 涤纶纤维。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。