有变形的

The results indicate that its dynamic stress-strain curve is hyperbolic type. The dynamic strain of LCES decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency when it is subjected to the same dynamic stress. At the same dynamic strain, the dynamic secant elastic modulus E_(sec of LCES increases and the damping ratio decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency. The curves ofσ_d～ε_d,E_～ε_d and D～ε_d with different EPS content intersect respectively, the trend of LCES deformation characteristic is inversely proportional to EPS content near the intersection. The value of dynamic strain at the intersection is about 0.5%~3.0%, the magnitude of which is related to the mixing proportions and confining pressure.

试验结果表明，LCES的动应力应变骨干曲线形态符合双曲线；在相同的动应力作用下，LCES产生的动应变随着固结压力、水泥掺量、试样养护龄期和振动频率的增大而减小；在动应变相同的情况下，随着固结压力、水泥掺量、试样养护龄期和振动频率的增大，LCES的动模量增大而阻尼比减小；随着加载次数的增大，LCES的动模量在开始阶段显著降低，然后趋于稳定，但当加载次数达到几百次时，动模量又有增大的趋势；不同EPS掺入比的LCES的动应力应变骨干曲线、动模量随应变变化曲线和阻尼比随应变变化曲线都发生了相交，交点前后EPS掺入比的大小对LCES动力变形特性的影响趋势是截然相反的，交点处的动应变值一般在0.5％～3.0％范围内变化，其大小与LCES的配比以及固结压力有关。

It is shown that Mn and Ti had refined the microstructure,and formed to precipitation affluent of Mn or Ti ,which approved the performance of the Shape Memory Alloy.For a certain strain,the shape memory effect vayied functionly together with the aging time:alloy performance the best coorperative status that the martensite lathing was close and ordered,the precipitation rich of Mn and Ti dispersed orderly in the microstructure and little or even no eutectoid phase had precipited in the alloy ,in a special aging temperature and time. With the prolonger of the aging time,the different aging time affects the microstructure rulely.

结果表明：Cu-Al-X系形状记忆合金中，Mn和Ti的加入细化了组织，并且形成了富Mn和富Ti相，起到沉淀强化和弥散强化的作用；对于同一种变形量，合金在母相时效时，形状记忆效应随时效保温时间呈现规律性变化，不同时效温度下，合金对应一个不同的时效时间，此时合金的显微组织呈现最佳自协作状态，马氏体板条细密有序，富Ti和Al相均匀的弥散在组织中，合金中没有或很少有共析相出现，且随着时效时间的延长，在不同的特定温度下，Cu-24Al-3Mn-2Ti合金的组织会有规律性的变化。

It is shown that Mn and Ti had refined the microstructure, and formed to precipitation affluent of Mn or Ti, which approved the performance of the shape memory alloy. For a certain strain, the shape memory effect varyied functionly together with the aging time: alloy performance the best coorperative status that the martensite lathing was close and ordered, the precipitation rich of Mn and Ti dispersed orderly in the microstructure and little or even no eutectoid phase had precipited in the alloy, in a special aging temperature and time. With the prolonger of the aging time, the different aging time affects the microstructure rulely.

结果表明：Cu-Al-X系形状记忆合金中，Mn和Ti的加入细化了组织，并且形成了富Mn和富Ti相，起到沉淀强化和弥散强化的作用；对于同一种变形量，合金在母相时效时，形状记忆效应随时效保温时间呈现规律性变化，不同时效温度下，合金对应一个不同的时效时间，此时合金的显微组织呈现最佳自协作状态，马氏体板条细密有序，富Ti和Al相均匀的弥散在组织中，合金中没有或很少有共析相出现，且随着时效时间的延长，在不同的特定温度下，Cu-24Al-3Mn-2Ti合金的组织会有规律性的变化。

The effect from transverse webs and frames and the effect from collision velocity on ship bow collision properties are also studied in this paper. 7. The idea of buffer bow is put forward from aspects of the overall situation of environmental protection and reducing the damage of struck shipside caused by striking bow. The influence of curvature of bow shape on mode of distortion, collision force, collision force density and energy absorption of bulbous bow is described detailedly through a series of collision numerical simulation for bulbous bows that have different curvature.

发现横向框架对于船艏结构的变形形态，碰撞力及能量吸收都有一定的影响，在进行碰撞分析时不能忽略，在较低的速度范围内碰撞速度对碰撞力及能量吸收没有太大影响，所以可以从较高速度撞击后得到的能量吸收曲线中得到较低速的碰撞能量吸收曲线，从而可以得到低速碰撞时的撞深，然后通过这个撞深在较高速碰撞的碰撞力曲线中可以获得低速碰撞的碰撞力曲线。

The ratchetting experiments of 316L and 1Cr18Ni9Ti stainless steel cyclically loaded under proportional and nonproportional conditions were performed respectively.

通过对两种不锈钢材料分别进行比例和非比例应力循环加载棘轮效应试验，揭示了两种不锈钢材料的棘轮效应的一些特征，和导致这些棘轮效应特征的原因，得到了一些有意义的结果，为建立能较为精确地描述结构在多轴应力循环下的累积变形的本构模型提供了一定的实验及理论分析依

Results indicate that the number of bacteria grown in media LB, CSEA and WSA was 14.84×10^7, 10.27×10^7 and 6.91×10^7 CFU per gram dry soil, respectively, after 192 h of incubation. The diversity index of soil bacteria was the highest in WSA, while the lowest in LB. Certain similarity was discovered in bacteria community between the three media, i. e. the Jaccard index was 57.69% between LB and CSEA, 53.13% between LB and WSA and 66.67% between CSEA and WSA. Phylogenetic analysis suggests that the dominant bacterial groups in the soil belong to β-Proteobacteria,γ-Proteobacteria and Actinobacteria. The sequence of 16S rDNA of some OTUs was found to have high homology with Burkholderiaceae bacterium, Rhodococcus and Mycobacterium, so it is presumed that the cells of these bacteria can secrete Resuscitation-Promoting Factors, which may effectively improve culturability of soil microorganisms.

结果表明，LB、CSEA、WSA培养基192h后每g干土获得的细菌数量分别为14.84×10^7、10.27×10^7和6.91×10^7CFU，但微生物多样性指数以WSA为最高，LB多样性指数最低；三种培养基培养的细菌菌群有一定的相似性，LB和CSEA培养基间的Jaccard指数为57.69%，LB和WSA培养基之间为53.13%，而CSEA和WSA培养基的相似性指数达66.67%；16SrDNA测序结果表明，所获得的土壤细菌优势种群在分类方面主要属于γ-和β-变形杆菌以及放线菌亚门，其中某些OTUs中的16SrDNA序列与Burkholderiaceae bacterium、Rhodococcus和Mycobacterium属具有较高的同源性，推测其细胞能够分泌复苏促进因子，有效地提高土壤细菌的可培养性。

Basing on this mode and his two invention patents, chooseing ANSYS as platform and linking the important project of JiLin province Science and technology ministry 'cylindrical and cone spurgears rolling preform and extrusion precise forming equipment research and manufacture for automobile'(NO.20030311), the author made the finite element numerical simulation about elasto-plastic large deformation heat-force couping of rolling preform and stamping-extrusion and bulge-extrusion combining precise forming for spur gear', investigated qualitativiely and quantitatively on the gears formability for the environmental and the blank parameters , summarized some useful conclusions.

本论文是我的导师宋玉泉教授关于&塑性精密成形&研究方向的一个组成部分，按照他所提倡的&科、教、产一体化&培养模式，并以他的两项发明专利为依托，立足于以ANSYS软件为模拟平台，密切结合吉林省科技厅重点项目&汽车用圆柱圆锥直齿轮滚轧和挤压精成形设备研制&(批准号：20030311)和吉林大学超塑性和塑性研究所&直齿轮中试生产线建设&，开展了对&圆柱直齿轮滚轧制坯－镦挤、胀挤复合精成形&的有限元弹塑性大变形热－力耦合数值模拟，对环境参数和轧件内部的参数对制件成形性的影响进行了定性和定量的研究，总结了一些有意义的结论。

The spiracles are bigger and more near dorsal line than all the others. Their trachea branches are taper and abundant and form short tracheoles. This gave the tufted form to the trachea, which appeared shrubby. The trachea branches that arranged in other segments gave them a tree-like look. They do not directly supply oxygen for tissues, but they suspend in the hemolymph and attach to the muscle of the heart, so that they can move in constant with the contraction of the heart muscle.②The 8th segment tracheal tufts have thinner cuticle and basal lamina than that of the other trachea, and have much pad cuticle, which is appropriate for them to move, and their basal lamina have small pores, which are favour of the permeation of gas.③Injecting the methylene blue into the larvae to label hemolymph, we observed that the hemolymph flow into the heart through the 8th segment tracheal tufts.④Normally these tracheal tufts have all kinds of hemocytes, which are abundant in the tufts. A large number of hemocytes released from tissues attach to the tufts by changing their structure when anoxic stress happen.

气管分支细短而丰富，形成气管簇，呈灌木丛状（其它各节气管则呈粗树干状分布），它不是直接给组织供氧，而是悬浮在血液中，与心肌相连接，随着心肌的收缩而不断运动；②气管簇的内膜及底膜都比其它各节的薄，且管壁内膜具有更多的适合运动的垫状表皮，底膜还有小孔结构，这有利于气体的通透；③向体内注射蓝色的亚甲基蓝标记血液发现，血液流动方向是经该气管簇后而流回心脏；④正常情况下，气管簇处有各种各样的血细胞聚集，当缺氧胁迫时有大量的血细胞从组织中释放出来，通过变形而紧贴气管簇，有利于气体的交换；⑤给体内注射无色的亚甲基蓝发现气管簇比其它各节更易变蓝，说明该处具有更高的获氧能力。

The forming experiment on hemisphere testified that the transforming pattern of MBWK fabrics was similar to woven fabrics under the condition of ignored yarns slippages. In the forming experiment on rectangular box, the obvious yarns slippages were observed during the forming process, so the pin-jointed net model used by woven fabrics didn't adapt to MBWK fabrics. Based on this finding, a new mathematical model using a macroscopic approach was established for predicting the unfolding shape of flat MBWK fabrics after deformation. In addition, the effect of position of constraint yarns on forming results was analyzed.

半球的织物成型实验证明了在纱线滑移可以被忽略的情况下，MBWK织物的变形规律和机织物相同；立方体的织物成型实验中，MBWK织物有明显的纱线滑移现象，机织物的成型模型不再适用，因此从宏观角度建立了全新的成型模型，并讨论了不同铺覆起始位置对成型效果的影响；对织物圆柱成型实验的研究主要着重于织物成型后纱线滑移现象的分析，描述了纱线在圆柱成型过程中的滑移特点及规律。

Because aluminum surface unlike composite aluminum foil paper and aucilisty paper, it has a certain amount of micro-small holes, moisture penetration into the paper can be, so it is important for moisture control; and aim at aluminum sheet piling up cannot be printed matter is exhausted, the card with a maximum of 3000, because aluminum is not wear-resistant surface, piling up too much will crush India face about note aluminized paper storage time should not be too long, it is best not more than two months, for a long time will be subdivisionof with the back of the paper, the following is issued on picking flowers; by the aluminum sheet business card printing and membership card making bearing in mind that when you heat curing temperatures not too high, too high a temperature can affect aluminum surface which flowers, and too hot paper antishrinking rise on deformation is too big to post processing.

因为真空镀铝纸的暗地不像不简单铝箔纸和PET纸，它有必定的微洪不小孔，水不合可以不合泌出纸，所以不差水不合的把持不一不合重给；③真空镀铝纸的印品堆放不克不及太众，卡纸最众不超功3000张，因为真空镀铝纸的暗地不耐磨，堆放太众会压伤印背；④夺纲真空镀铝纸的不领取工夫不给太不幼，最好不给超功两个日，因为工夫不幼了暗地会跟纸的背后粘连，变成纸背发不攒；⑤真空镀铝纸的制卡和会员卡制息给夺纲冷固化时温量不给太矮，温量矮了会感化真空镀铝纸的暗地，使其变不攒，而且太冷纸张缩涨变形太不小，不差后增工感化很不小。

I can still vividly recall the impressive scenes you gave. You were among my friends and relatives who accompanied me from my house to the seaport and when the porters were slow to show up, you obligingly carried my suitcase for me.

你对我的种种感人情意，使我记忆犹新，那天你随着我的亲友从家里送我上轮船，搬运工迟迟不来，你毅然替我提着皮箱上船。

St. Nicholas became the patron saint of Russia, where he was famous for his red cape, flowing white beard, and bishop's mitre.

圣尼古拉成了俄罗斯人的守护神，在那里，他以身披红斗篷，留着飘逸的白胡须，戴着主教法冠而闻名。