有...条件

The reliability of analysis result depends largely on the in-house experimental conditions. Unlike the previous analysis that only concerns the sole effect of permeable pressure, this article considers both permeable and confining pressure and deformation characteristics of concrete material under the interaction of them according to the real work state of construction, which may leads to the changing pattern of permeable rate as listed below: permeable rate always reaches its peak with the time process going on, than goes down and remains straight on some certain value; The PR will tend to decline while the confining pressure is increased, and the time taken before the peak will be extended as well; Under the constant permeable pressure and circularly changing confining pressure, the minus-exponential ascend and descend relationship could be applied between the PR and Time axes respectively with crannied and intact concrete samples, and the PR of crannied concrete is far more larger than that of intact concrete. The change pattern of concrete could also be mathematically analogized using the least square method.

室内的实验条件是研究成果可靠性的重要因素，而以往的研究都只考虑了渗透压单一作用，本文根据混凝土结构的实际工作状态，同时考虑了围压与渗透压共同作用下的混凝土材料的渗透性变化特征，得出了混凝土材料在围压作用与渗透压共同作用下的渗透率的变化规律：渗透率都是随时间推移先达到一个峰值，再降低并趋于平稳；渗透率会随围压的增大而减小，并且峰值的到达时间也会随之延长；在渗透压不变，围压升降循环的情况下，有裂缝、无裂缝混凝土的渗透率变化规律是随时间成负指数关系上升、下降，且有裂缝混凝土试件的渗透率远远高于无裂缝混凝土的渗透率，并对混凝土的变化规律运用最小二乘法进行数学拟合。

Experiments show that when starch and scattered mediums are different, under the same condition, the hardness and crispness of products are different.

实验表明，在相同条件下，当淀粉与分散介质的比值不同时，成品的硬度、脆度有显著差异；当分散介质不同时，成品的硬度、脆度也有显著差异。

The results showed that:①the crystalline phases are mainly the cuspidine, wollastonite and gehlenite with nepheline, fluorite and olivine also found in some samples under the experimental conditions;②with the bacisity and CaF_2 content increased, crystalline proportion of mold flux rises .

熔融保护渣在MoSi2高温电阻炉内以2℃/min降温速率冷却至室温，制成薄片，采用岩相显微镜分析保护渣的结晶矿相·结果表明：在本实验条件下，结晶矿相主要有枪晶石，硅灰石，黄长石，个别渣样有霞石，萤石，橄榄石；增大保护渣碱度，能促进保护渣结晶；随着渣中CaF2，Na2O，K2O和Li2O质量分数的增大，保护渣结晶化率增大；随着渣中Al2O3，MgO，BaO和MnO质量分数的增大，保护渣结晶化率减小

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Changes in Xc for different pulp cellulose fibers are not the same during the ultrasonic treatment. Crystallization and decrystallization may both exist during the treatment at the conditions of lower-intensity ultrasonic wave. After treatment with ultrasonic Xc of MBKP cellulose is decreased and that of EBKP is increased. The changes of Xc of different pulp cellulose are more closely correlated to the fibers' morphology size and the cavitation state. The maximum Xc of 84% is obtained when BEKP cellulose is treated under the conditions of ultrasonic frequency f=23-25kHz, power=400w, and treatment time t=720s.

不同原料来源的纤维素纤维，由于形态尺寸和超分子结构的差异，经超声波处理后超分子结构表现出不同的变化规律；超声波处理过程中，结晶和消晶两种作用同时存在；超声波功率对纤维素的结晶度有较大的影响，对晶体尺寸有一定程度的影响，但结晶度Xc与超声功率没有线性关系；在频率为23-25kHz，功率为400W条件下，对桉木漂白浆纤维进行超声波处理，可获得高结晶度（84%）的纤维素样品。

Feudal superstition tends to spread in the countryside under self - governance by village residents. There are many reasons, such as historical reasons, descensive authority of Rural grassroots organization, dispersed economy, the construction of spiritual civilization lags behind, and so on.

在村民自治条件下，一些农村封建迷信大有抬头蔓延的趋势，农村封建迷信泛滥的原因有历史的遗留、农村基层组织权威的下降、经济分散化、精神文明建设滞后、社会大环境的影响。

The Cognitive Meaning of Proposition means whether it's true or not. The standards about the cognitive meaning of propositions are five, such as conceivable principle?describable principle?truth principle?confirmed principle and verified principle.

命题的认知意义是指其有无真假可言；判断一个命题是否具有认知意义，有五个不同的标准：可想象性原则，描述性原则，真值条件原则，可证实性原则和印证原则。

The thermal decomposition of the copper acetate dihydrate in a static air atmosphere was investigated by TG-DTG techniques.

用 TG-DTG 和DSC研究了TNPG·2/3H2O的热分解过程，在10℃·min-1的升温条件下，其熔点为167℃，有两个吸热阶段，有两次质量损失过程，在熔化时剧烈放热分解。

According to the above-mentioned experiments, the study select discriminable data which form discriminant function and make discriminant analysis on the objects (students from junior Grade Two and senior Grade Two, with academic achievements ranging from excellence, ordinariness, to failure) with ten members in each group, which leads to a discriminant system of middle school students with different academic achievements.Ⅳ.

本研究研制和开发了WACOM-2005-1型数码写字板，采用手书运动分析技术，分别选择初二、高二年级学优生、中等生、学差生各12至24人进行研究，从自然手书运动、控制性手书运动、在不同压力状态下的手书运动以及手书运动学习四个方面，通过8个系列实验，探索了左右手、有无视觉参与的自然手书运动特点；定点直线、追随手书的控制性手书运动特点；数字认知压力、汉字认知压力、情绪变化、有无噪音条件下的手书运动特点；手书运动学习的特点。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。