最大误差

Through the stress calculation of a 3d jacket platform in wave, the change of load combination acting on the braces of multiplanar joints was observed, the influence of different load combination on the maximum stress and the location of hot spot was revealed, and the error in stress estimation caused by regarding multiplanar joint as uniplanar joint was analyzed, which shows the necessity of stress analysis to multiplanar joints.

本文通过一座波浪中的三维导管架平台结构的接头应力分析，考察了接头的载荷组合形式随波浪的变化，揭示了不同的载荷组合形式对接头最大应力及其热点位置的影响，分析了将空间接头作为平面接头来估算最大应力时引起的误差，从而说明了进行空间接头应力分析的必要性。

The most great characteristic of supporting vectorial mechanism theory is to collect by limited training little error that sample get can assurance collect and still keep the small error to independent test.

支持向量机理论的最大特点是由有限的训练集样本得到的小的误差能够保证对独立的测试集仍保持小的误差。

The results show that NPP is larger in June and July than other growth periods, grass LAI and NPP change rapidly from May to June. Estimated error of 44 cases by the biomass model is less than 20%, which show that the biomass model is very good , the model can describe growing status. Photosynthesis and respiration are different because of different type grass , three types grass are more adaptive to desert environment and the biomass are also big, the grass types include Alhagi sparsifolia, Lycium ruthenicum and Reaumuria songarica. The grass biomass is influenced by many factors such as grass type, total cover and plant height et al.

结果表明，2005年牧草生长期内NPP的变化基本是6、7月份最大，其它月份较小，5～6月份是牧草叶面积变化比较大的时期，也是NPP变化比较显著的时期；生物量模型估算得到的44个样本的生物量误差基本都小于20%，说明模型能够反映牧草的实际生长状况；不同荒漠牧草对光的利用能力和对CO2同化能力有很大差异，骆驼刺、红砂、黑果枸杞是荒漠牧草生物量较大的牧草类型；牧草类型、牧草盖度以及平均高度是造成不同牧草产量相差较大的重要原因。

A robust output feedback controller is advanced by using the DRNN-based observer presented above, so that the output-matching and lipschitz conditions are not imposed on the uncertainties; Robust adaptive controller is used in a class of nonlinear systems based on neural networks and H〓 methods, thereby the constraint on uncertainties with largest known boundness is removed, not as in H〓 methods.

利用本文的动态神经网络鲁棒观测器，设计了鲁棒输出反馈控制器，取消了已有结果对未知动态的输出匹配条件的限制；结合静态神经网和H〓控制方法，对一类非线性系统设计了鲁棒自适应反馈控制器，克服了H〓控制要求不确定性最大可能界已知的不足，其最大优点是仅要求网络逼近误差有界，且不要求网络权的离线训练。

Results :Satisfactory facial appearance was achieved in all the patients . Results showed that the repeatability was 100% when error tolerance was 3.5 mm. If tolerance was set at 2 mm, the repeatability was 97.8%.The biggest difference occurred in ramous area.

结果：5例患者均获得满意的术后形态，在差值分析分析中，设允许误差为2mm，真实术后与虚拟手术的吻合程度为97.8%；设允许误差为3.5mm，两者吻合程度为100%；最大差别产生的区域在双侧升支。

Calculation formulae were derived for the maximum angle error of the outputting gear caused by the tangential synthetic tolerance and the last motion error angle caused by normal directional side clearance.

推导出了由切向综合公差引起的输出齿轮最大角度误差的计算公式和由法向侧隙引起的空回误差角的计算公式。

The comparison is made about the RELAX and ML, the RELAX-AS and the ML-AP, The weightiest characteristic of the current estimation of the signal parameter in getting the new estimation in the RELAX-AS was found.

这种最大依赖性使得松弛算法的交替分离解法收敛速度非常慢-这是松弛算法的交替分离解法的严重缺陷，这种最大依赖性使得松弛算法的交替分离解法在有系统误差时能够有效地抑制局部极值，这是它的一个重要性能。

To guarantee tracking precision, the relation between the tracking control error and the output torque of the controller is analyzed from the point of engineering. Then an effective replanning scheme is presented, where fuzzy logic is used to weight the maximum joint torque according to the control error.

为保证跟踪精度，从工程的角度分析了跟踪控制误差与控制器输出力矩的关系，提出了根据控制误差对关节最大力矩进行模糊加权的二次规划方案，是一种便于实际工程应用的有效方法。

Corrugated box production equipment has: fully automatic four-color ink printing slotting machine, the largest print size 1200mmX2600mm, chromatic walk-bit error 1mm, can be reached through the network simulation chromatic color effects; large-scale two-color printing presses, the largest print size 2400mmX3300mm, can provide customers with super-large carton printing services.

瓦楞纸箱生产设备有：全自动四色水墨印刷开槽机，最大印刷尺寸为1200mmX2600mm，套色走位误差《1mm，可通过网点套色达到模拟彩色效果；大型双色印刷机，最大印刷尺寸为2400mmX3300mm，可为客户提供超大型纸箱印刷服务。

It is indicated that the accuracy of the measured value is determined rather by the practical relative error than by the maximum relative error. It is correct that the nearer the scale reading approaches the maximum, the more accurate the measurement is. The scale reading need not be required above 2/3X.

指出使用电表进行测量时，测量值的准确性是由其实际相对误差而非最大相对误差决定的；并非电表的读数越接近满刻度，测量值的准确性就越高；使用电表进行测量时，电表的读数不必被限定在2/3X上。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。