最大误差

Phase velocity error caused by position error of microtremor observation array is computed under different conditions such as two different dispersive phase velocity models of Rayleigh wave, three kinds of radius, 19 kinds of observation position mode and 6 types of position error.

为研究地脉动观测台阵中观测点之间的定位误差带来的影响，计算了在两种瑞利波频散模型、3种不同的圆周半径以及19种观测位置等多种情况下由6种定位误差引起的瑞利波相速度相对误差，结果表明：由于圆周上观测点数目有限，在不存在定位误差时，相速度误差也是存在的，随观测点位置的不同，相速度相对误差存在差异，其最大值约为最小值的3倍。

According to the definition of the relative error, the incorrect expression of the maximum relative error is corrected. The author analyses the distinction between the maximum relative error and the practical relative error.

根据相对误差的定义，纠正了教材中测量值的最大相对误差表达式中的错误，分析了最大相对误差和实际相对误差的异同。

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

Finally, a high-order orthogonal polynomial method is used to compensate the Pt resistor nonlinearity and the high precision of compensation is proved by comparison tests of the temperature measuring module and the absolute standard Pt resistance thermometer.

使用高阶正交多项式拟合法对Pt电阻的非线性进行了补偿，给出了该系统温度测量模块测量数据与一级标准铂电阻温度值的比较实验，在不同的温度点，该温度测量系统的最大误差为0.000 6℃。

Without false paths, the errors of evaluation delay and precharge delay are within 3.62% and 8.26% respectively.

如果不考虑伪路径的影响，求值方向和预充方向延时的最大误差分别为3.62%和8.26%。

The monotony and extremum theory of function are applied to prove the geometrical characteristic of error hand for 2D linear segment uncertainty ε(subscript σ) model in theory. The result shows that the error hand has the geometrical shape of "larger ends and smaller middle" or "one end larger and the other smaller". The minimum width and its exact position of the error hand are calculated too. It is proved that the minimum width position of the error hand is near the end with the smaller mean square error.

运用函数单调性和极值理论，从理论上证明ε模型的误差带的几何特征；得到线元误差带不仅具有&两端大、中同小&，而且也可能具有&一端大、一端小&的几何形状；给出了误差带的最小带宽及其位置；论证了误差带的最小误差带宽的位置靠近中误差较小的一端。

The method was used to retrieve PAR in Shandong and the result was tested by the ground data in Yuncheng station of CERN with the error less than 10%.

将该算法应用于对华北平原的部分区域进行反演，并使用中国生态网络禹城试验站的自动测量数据对结果进行检验，最大误差在10%以内。

The complexity of bodywork decides variety of it's error. The station and primary factor which cause error is inconstant change and using correlation analysis can find out the primary factor. With an project given, the theory of correlation analysis for dimension variation of bodywork is discussed through correlation analysis and the layer structure of the bodywork,the state in which the error happened can be found out. How to use eigenva...

车体装焊的复杂性决定了误差产生的多因素性，车体制造过程中产生误差的工位和主要因素是不断变化的，采用相关性分析方法从众多的误差根源中准确地发现最主要的误差源；结合工程实践，论述了车体尺寸波动的相关性分析方法的原理，根据测量点的相关性分析和车体焊接工艺的层次结构，可准确地找到产生车体尺寸误差的工位；讨论了如何利用相关系数矩阵的特征值和相应的特征向量判断尺寸波动的模式，指出测量数据的波动主要按最大特征值所对应的特征向量方式波动，引起这种波动的原因是车体误差产生的主要原因，应重点采取措施加以控制；提出了应用计算机进行相关性分析的解决方案。

They are derived in a cl...

在所有的情况下，近似解的最大误差均小于2～3米。

The maximum error by the proposed approach among 180 phase samples for each CiR is inspected.

考察了每个CiR的180个不同相位算例的最大误差。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。