最大误差

At the same time, SVM is also used to identify the well interpretation model. The most relative error of curve fitting is 0.9623%.

同时，将支持向量机用于试井压力恢复曲线的拟和，拟和的最大相对误差为0.9623％。

The working frequency is equal to or less than the permissible error limit of measurement frequency of the resistance box..

电阻箱的工作频率等于或低于测试频率上限时的最大允许误差。

Also, the effect of state estimation error and delay to the maximum communication interval is analyzed.

分别在状态反馈、输出反馈和离散情况下，研究了基于状态预估的网络控制系统的建模、稳定性分析、控制器设计和仿真，分析了数据链路的增加，状态估计误差和延时对最大通讯间隔的影响。

According to the expression set from the Guide to the Expression of Uncertainty in Measurement, the judgment and the expression of the maximum permissible error of the tilt meter and strain meter have been determined.

按照新的国际通行的《测量不确定度表示指南》所规定的测量不确定度的表示方法，确定了地壳形变观测仪中倾斜仪、应变仪最大允许误差的表示和判别。

With coupler embedded and acceleration sensitivity compensation design, the structure symmetry is insured, which can induce the acceleration sensitivity effectively. The acceleration sensitivity compensation design also improves the production efficiency of FOH for towed linear array application.2. A good theoretical simulation platform, utilizing the method of elastic mechanics and the finite element method, is established, which can provide an effect predictive design for FOH. The experimental results are in good agreement with the theoretical analysises.3. Some key technology problems in the making of FOH for towed linear array application are conquered. The new developed FOH, with an acoustic sensitivity of -143.0dB, has acceleration sensitivity less than -30dB, which exceeded to results from other international reports.

本论文的主要成果和创新在于：1、提出了耦合器内嵌、带加速度灵敏度微调补偿的低加速度灵敏度光纤水听器结构，最大程度保证了工艺结构的对称性，实现了对工艺误差的有效补偿，提高了低加速度灵敏度光纤水听器研制的成品率。2、采用弹性力学和有限元方法建立了拖曳线列阵光纤水听器理论设计平台，实验与理论分析结果相一致，这为优化光纤水听器的结构设计提供了有效的技术手段。3、解决了拖曳线列阵用光纤水听器制造的关键技术问题，研制出声压灵敏度为-143.0dB，加速度灵敏度低于-30dB的拖曳线列阵用光纤水听器，其加速度灵敏度优于国际上已报导的结果，并在国防水声一级计量站对其进行了性能指标测试(来源：A14BC论文网www.abclunwen.com)。

While carrying out simulative program design for hobbing machining,the most difficult point is the description and modelling on the relationship between the cutter and gear blank both in space and in motion,especially the modelling of motion relation between cutter and gear blank in case there exists factors of error.

在进行滚齿的切削仿真程序设计中，其中最大的难点是对刀具和轮坯的空间关系和运动关系的描述和建模，尤其是存在误差因素时对刀具和轮坯之间运动关系的建模。

On the basis of the model, distribution of the first four order natural frequency is analyzed within workspace of the manipulator. Displacement error of moving platform is studied under excitations of external forces and inertial force. Maximum dynamic stress in each time and position of its occurrence are given.

在该模型的基础上，分析了机械手在工作空间的前四阶固有频率的分布情况；研究分析了在外力和刚体惯性力激励下机械手动平台的位置误差；给出了构件在各个时刻的最大动应力及其出现的位置。

To make the constant in the interpolation error independent of element size,the ratio of the diameter of the element and the diameter of the biggest ball contained in the element,is uniformly bounded.

传统的有限元方法误差估计需要满足正则性条件或非退化条件，即：单元的直径和单元的最大内切圆直径的比值是一致有界的。

According to the basic principle of telluric current prospecting and general formula of derived subsurface leakage, three dimensional distribution of relative errors about the earth resistivity and plane isopleth map were put forward,with the maximum value of leakage current allowable by" The Technical Specification on Geoelectric Observations".

根据电法勘探的基本原理。参考已推导出的线对地漏电的基本公式。给出了《地电观测技术规范》允许漏电电流最大值时的电阻率相对误差三维分布图及平面等值线图，并讨论了其分布特征

We calculate the regression curve about length of erased magnetic record and lightning current peak. We analyze the error of recording data and find a new means about direct measurement of the max lightning steepness with magnetic tapes.

作出磁带消磁长度与霄电流峰值的拟合曲线，对测量数据进行误差分析，找到利用磁带直接测量雳电流最大陡度的新方洁。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。